QuickServer Start-up Guide Table of Contents
FieldServer Technologies 1991 Tarob Court Milpitas, California 95035 USA Web: www.fieldserver.com
Tel: (408) 262 2299 Fax: (408) 262 2269 Toll Free: (888) 509 1970 email: support@fieldserver.com
TABLE OF CONTENTS
1 Equipment Set-up .......................................................................................................................................................... 4
2 Supplied equipment ....................................................................................................................................................... 4
2.1 BTL Mark – BACnet Testing Laboratory .......................................................................................................................... 4
2.2 LonMark Certification ..................................................................................................................................................... 4
3 Mounting ....................................................................................................................................................................... 5
3.1 Dimensions ..................................................................................................................................................................... 5
3.1.1 Dimension Drawing FS-QS-1X10-XXXX ................................................................................................................... 5
3.1.2 Dimension Drawing FS-QS-1X11-XXXX ................................................................................................................... 6
3.1.3 Dimension Drawing FS-QS-12XX models with RS-422 ............................................................................................ 7
3.2 Wiring ............................................................................................................................................................................. 8
3.3 Specifications.................................................................................................................................................................. 9
4 Installing the QuickServer ............................................................................................................................................ 11
4.1 RS-485 .......................................................................................................................................................................... 11
4.1.1 RS-485 Connection R2 port ................................................................................................................................... 11
4.1.2 RS-485 Connection R1 Port (Only on Non-LonWorks QuickServers) ..................................................................... 11
4.2 QuickServer LonWorks – (FS-QS-1011-XXXX or FS-QS-12X1-XXX) ............................................................................... 12
4.3 QuickServer KNX – (FS-QS-1011-XXXX or FS-QS-12X1-XXX) ......................................................................................... 12
4.4 RS-232 Connection R2 Port (Only available on the FS-QS-12XX Models)..................................................................... 13
4.5 Configure the DIP Switches .......................................................................................................................................... 13
4.5.1 Using A0 – A7 to set Node ID/Device Instance. .................................................................................................... 13
4.5.2 Using B0 – B3 to set Baud Rate ............................................................................................................................ 14
4.5.3 DIP Switches S0-S3 ................................................................................................................................................ 14
5 Operation ..................................................................................................................................................................... 15
5.1 Power up the device ..................................................................................................................................................... 15
5.2 Connect the PC to the QuickServer over the Ethernet port. ........................................................................................ 15
5.3 Connecting to the QuickServer .................................................................................................................................... 16
5.3.1 Using the Toolbox application to Allocate the IP address: ................................................................................... 16
5.4 Set IP Address of the QuickServer ................................................................................................................................ 17
5.4.1 Using the Toolbox Application to set the IP address: ........................................................................................... 17
5.4.2 Using the Web GUI to set the IP address: ............................................................................................................. 18
6 Configuring the QuickServer ......................................................................................................................................... 20
6.1 Retrieve the Sample Configuration File ........................................................................................................................ 20
6.2 Change the Configuration File to Meet the Application .............................................................................................. 20
6.3 Load the Updated Configuration file ............................................................................................................................ 21
6.3.1 Using the Toolbox application to load a configuration file: ................................................................................. 21
6.3.2 Using the Web GUI to load a configuration file: ................................................................................................... 23
6.4 Test and Commission the QuickServer ......................................................................................................................... 24
Appendix A Useful Features ................................................................................................................................................. 25
Appendix A.1. QuickServer DIP Switch configuration .............................................................................................................. 25
Appendix A.1.1. Configure DIP switches A0-A7 .................................................................................................................... 25
Appendix A.1.2. Configure DIP switches B0 – B3 .................................................................................................................. 25
Appendix A.1.3. Configure DIP switches S0 – S3 .................................................................................................................. 26
Appendix A.2. RS-422 Connection R2 Port (Only available on the FS-QS-12XX models) ......................................................... 27
Appendix A.2.1. Connection and Operation of the RS-422 QuickServer ............................................................................... 28
To Next Page
Loading...