FieldServer QuickServer 12 0 Series - Dimension Drawing FS-QS-12 XX Models with RS-422

44 pages

Save Page as PDF

To Next Page

To Previous Page

QuickServer Start-up Guide Page 7 of 43

FieldServer Technologies 1991 Tarob Court Milpitas, California 95035 USA Web: www.fieldserver.com

Tel: (408) 262 2299 Fax: (408) 262 2269 Toll Free: (888) 509 1970 email: support@fieldserver.com

3.1.3 Dimension Drawing FS-QS-12XX models with RS-422

R1 Port

R2 Port

Main Page

Table of Contents2
Equipment Set-Up4
Supplied Equipment4
BTL Mark - Bacnet Testing Laboratory4
Lonmark Certification4
Mounting5
Dimensions5
Dimension Drawing FS-QS-1X10-XXXX5
Dimension Drawing FS-QS-1X11-XXXX6
Dimension Drawing FS-QS-12XX Models with RS-4227
Wiring8
Specifications9
Installing the Quickserver11
RS-485 Connection R2 Port11
RS-485 Connection R1 Port (Only on Non-Lonworks Quickservers)11
Quickserver Lonworks - (FS-QS-1011-XXXX or FS-QS-12X1-XXX)12
Quickserver KNX - (FS-QS-1011-XXXX or FS-QS-12X1-XXX)12
RS-232 Connection R2 Port (Only Available on the FS-QS-12XX Models)13
Configure the DIP Switches13
Using A0 - A7 to Set Node ID/Device Instance13
Using B0 - B3 to Set Baud Rate14
DIP Switches S0-S314
Operation15
Power up the Device15
Connect the PC to the Quickserver over the Ethernet Port15
Connecting to the Quickserver16
Using the Toolbox Application to Allocate the IP Address16
Set IP Address of the Quickserver17
Using the Toolbox Application to Set the IP Address17
Using the Web GUI to Set the IP Address18
Configuring the Quickserver20
Retrieve the Sample Configuration File20
Change the Configuration File to Meet the Application20
Load the Updated Configuration File21
Using the Toolbox Application to Load a Configuration File21
Using the Web GUI to Load a Configuration File23
Test and Commission the Quickserver24
Appendix A Useful Features25
Appendix A.1. Quickserver DIP Switch Configuration25
Appendix A.1.1. Configure DIP Switches A0-A725
Appendix A.1.2. Configure DIP Switches B0 - B325
Appendix A.1.3. Configure DIP Switches S0 - S326
Appendix A.2. RS-422 Connection R2 Port (Only Available on the FS-QS-12XX Models)27
Appendix A.2.1. Connection and Operation of the RS-422 Quickserver28
Appendix A.3. KNX Connection R2 Port29
Appendix A.4. M-Bus Connection R2 Port30
Appendix A.5. Enhanced Network Security30
Appendix B Troubleshooting Tips31
Appendix B.1. Communicating with the Quickserver over the Network31
Appendix B.2. Technical Support31
Appendix B.3. Notes Regarding Subnets and Subnet Masks31
Appendix C Limited 2 Year Warranty32
Appendix D Reference33
Appendix D.1. LED Functions33
Appendix D.2. FS-QS-1010-XXXX Led's34
Appendix D.3. FS-QS-1011-XXXX Led's35
Appendix D.4. Quickserver FS-QS-101X DCC36
Appendix D.5. Compliance with UL Regulations36
Appendix D.6. Address DIP Switch Settings37
Appendix D.7. Baud DIP Switch Settings43

FieldServer QuickServer 12 0 Series - Dimension Drawing FS-QS-12 XX Models with RS-422

Table of Contents