Flowserve Limitorque L120-190 - How to Order Parts

To Next Page

To Previous Page

Limitorque

L120-190 through L120-2000 FCD LMENIM1203-01-A4 – 05/15

ﬂowserve.com

To order parts or obtain further information about your Limitorque L120 valve actuators, contact your

local Flowserve Limitorque distributor, sales ofﬁce, or:

Flowserve Limitorque

5114 Woodall Road

P.O. Box 11318

Lynchburg, VA 24506-1318

Phone (434) 528-4400

Fax (434) 845-9736

To ﬁnd the nearest Limitorque distributor or sales ofﬁce near you, go to www.limitorque.com

All inquiries or orders must be accompanied by the following information:

1. Actuator Size

2. Order Number

3. Serial Number

This information can be found on the Limitorque nameplate afﬁxed to the actuator.

How to Order Parts

Main Page

Table of Contents3
Introduction5
Purpose5
User Safety5
Initial Inspection and Storage Instructions6
Product Identification7
Inspection and Recording8
Short-Term Storage (Less than 1 Year)8
Figure 2.1 - L120-190 through 20008
Actuator Weights10
Table 3.1 - Actuator Weights10
Installation Instructions11
Safety Precautions11
Safety Practices12
Actuator Preparation12
Mounting Base13
Stem Acceptance13
Double Torque Switch13
Figure 4.1 - Double Torque Switch13
Table 4.1 - Mounting Base Dimensions13
Table 4.2 - Maximum Stem Acceptance13
Setting Torque Switch14
Figure 4.2 - Setting Torque Switch14
Balancing Torque Switch15
Torque Switch Terminal Connections15
Figure 4.3 - Ring Tongue Terminal15
Geared Limit Switch - Rotor Type16
Setting Limit Switch16
Table 4.3 - Terminal Dimensions by Cable Size16
Figure 4.4 - Geared Limit Switch17
Table 4.4 - Maximum Drive Sleeve Turns17
Figure 4.5 - Setting Geared Limit Switch18
Combination of Contacts19
Position Indication19
Local Position Indication19
Figure 4.6 - Position Indicators19
Remote Position Indication20
Calibrating Position Transmitter PT20SD20
Figure 4.7 - Typical Connection for a 1000 Ohm Potentiometer20
Operation21
Electrical Start-Up21
Typical Wiring Diagram22
Manual Operation22
Motor Operation23
Torque and Travel Limiting23
Maintenance24
Lubrication24
Lubrication Inspection24
Factory Lubricant25
Table 6.1 - Lubricant Weights25
Disassembly and Reassembly26
L120-190, -420, and -80026
To Replace Stem Nut Only26
L120-190, 420, 800 Disassembly27
Reassembling Actuator Sizes L120-190, -420 and -80028
Gaskets29
Figure 7.1 - L120-190 and -420 Drive Sleeve Side View (Refer to Table 8.1 for Parts List)30
Figure 7.2 - L120-190 and -420 Worm Shaft Side View (Refer to Table 8.1 for Parts List)31
Figure 7.3 - L120-190 and -420 Top View (Refer to Table 8.1 for Parts List)32
Figure 7.4 - L120-800 Drive Sleeve Side View (Refer to Table 8.1 for Parts List)33
Figure 7.5 - L120-800 Worm Shaft Side View (Refer to Table 8.1 for Parts List)34
Figure 7.6 - L120-800 Top View (Refer to Table 8.1 for Parts List)35
Table 7.1 - L120-190, -420 and -800 Typical Parts List36
L120-200038
Drive 2 Disassembly (Thrust Housing Only)38
Drive 1 (Torque Housing) Reassembly40
Drive 2 (Thrust Housing Only) Reassembly42
Figure 7.7 - L120-2000 Drive Sleeve Side View (Torque Base) (Refer to Table 8.2 for Parts List)43
Figure 7.8 -L120-2000 Top View (Refer to Table 8.2 for Parts List)44
Figure 7.9 - L120-2000 Side View (Refer to Table 8.2 for Parts List)45
Figure 7.10 - L120-2000 Exploded View46
Table 7.2 - L120-2000 Typical Parts List47
Standard Wiring Diagrams49
Figure 8.1 - Wiring Diagram - no Controls49
Figure 8.2 - Wiring Diagram - Integral Controls50
Figure 8.3 - Wiring Diagram - NCU51
Troubleshooting52
How to Order Parts53
EC Declaration of Conformity54

Flowserve Limitorque L120-190 - How to Order Parts

Table of Contents

Related product manuals