34
gear lever and the power takeoff lever.
2) Remove the control rods (2 and 3 Fig. 5) and put
them aside.
3) Deeply pull the lever (5 Fig. 5) and rotate the
handlebars 180° until you reach the right groove.
Then release the lever (5 Fig. 5).
IMPORTANT: To avoid damaging the control
cables, the rotation must be made following
the direction of the pictograms applied on the
machine (11 Fig. 5).
By rotating the handlebars 180°, the levers (PTO
control and speeds) and the rods (2-3 Fig. 5) are
reversed.
WARNING
The rods (2 and 3 Fig. 5) must not be taken out of
the supporting hole (9 Fig. 5) and are inserted in the
seats that are located in their direction.
4) Reassemble the control rods (2 and 3 Fig. 5) that
are located in their direction and secure them with
the elastic pins.
5) Make sure that the wheels are assembled properly
and that the arrow on the tyre sides corresponds
to the forward movement of the machine, other-
wise exchange them; otherwise, wheels must be
reversed.
6) Arrange the cables so that they do not perform
sharp or anomalous turns: make them to perform
the most logic route.
4.1.2 TYRES AND WHEEL THREAD
ADJUSTMENT
The machine in the standard model is usually
equipped with width adjustable wheels:
To increase or decrease the motor cultivator’s wheel
tread (Fig. 9):
- Lift the machine (See ch. «3.1 Transport»).
- Remove the xing bolts (1).
- Change the position of the internal disc (3).
- Insert the bolts and x them.
The variations in the roadway are 3 possible:
1) As shown in Fig. 9
2) By moving the disk (3) from the mounting holes
ref. 1 to the xing holes ref. 2.
3) By turning the wheel external member (4) upside
down in relation to the internal disk (3).
Check that the wheels are assembled in the correct
direction. Otherwise exchange them.
4.1.3 ASSEMBLY OF THE BAR AND SELECTION
OF THE SPEED RATES AND THE INSERTIO PTO
BAR
For reasons of packing, the rods (2 and 3, Fig. 5)
above, are removed from the machine and, therefo-
re, after placing the handlebars, t the rods into the
holes of the support 9 in Fig. 5, paying attention to
the fact that they must be arranged as shown in Fig.
7 ref. A and B.
Then insert the ends of rods in their seats (6, Fig. 5)
and secure it with the special spring pins (1, Fig. 5).
4.1.4 REPLACEMENT OF THE INTERCHANGE-
ABLE EQUIPMENT
To replace the interchangeable equipment, you must:
- securely lock the machine;
- unscrew the two nuts applied on the two studs (7,
Fig. 5) that connect the accessory to the PTO gear
(10, Fig. 5);
- remove the two washers and the accessory being
careful not to damage the thread of the studs;
- then take the accessory to connect and insert it into
the PTO;
- let match the grooved section of the accessory with
the PTO and complete the insertion;
- insert the two washers and two nuts and lock well
by screwing them progressively alternately to allow
the tool to be centered in the gear seat.
When you true up the attachment on the union
sleeve of the power takoff, pay attention not to
damage it.
DANGER
Before installing the equipment on the PTO (10 Fig.
5), make sure that this is clean and well lubricated
with grease.
This operations must be carried out by two people
wearing strong gloves.
All the towed accessories (plough, tank, trailer)
must be connected to the motor cultivator at the
cupling (8 Fig. 5) with the special pin and its
safety pin.
N.B. It is strictly forbidden to connect any inter-
changeable attachment not in compliance with the
safety and health regulations in force and therefore
without the «EC» brand.
It is better not to use accessories that are not
ENGLISH
To Next Page
Loading...