Franklin Electric Inline 400

Other manuals for Franklin Electric Inline 400

Installation And Operation Manual60 pages

Questions and Answers

R
Richard ShannonAug 18, 2025
What to do if my Franklin Electric Industrial Equipment unit runs continuously?
- R
  Ronald MccallAug 18, 2025
  If your Franklin Electric Industrial Equipment unit runs or cycles continuously, it may be due to a leak or usage exceeding ½ gpm (1.9 lpm) in the system plumbing. In this case, repair all plumbing leaks. Another cause may be that the internal non-return (check) valve is blocked or damaged. Place a new non-return (check) valve before the unit in INLET plumbing. Also, the internal flow piston might be stuck open, so clean the flow piston.
P
Patrick HortonAug 23, 2025
How to fix a Franklin Electric Industrial Equipment unit that cycles ON/OFF rapidly?
- E
  Erin MerrittAug 23, 2025
  If your Franklin Electric Industrial Equipment unit continuously cycles ON/OFF (Rapid Cycle), it could be due to improper charge pressure in the tank. Set the pressure in the pressure tank to 2 psi lower than the cut-in pressure. Another possible cause is the check valve between the tank and unit. Place the check valve after the pressure tank.
R
robertkochAug 26, 2025
What to do if my Franklin Electric Industrial Equipment unit won't turn on and no LEDs are lit?
- M
  Marcus ScottAug 26, 2025
  If your Franklin Electric Industrial Equipment unit will not turn on and there is no green or red LED illuminated on the control cap, it is possible that the circuit breaker tripped or turned off. Turn on the circuit breaker. If the problem persists, consult a licensed electrician to properly wire the Outlet/Junction Box.
S
susan67Aug 27, 2025
What to do if my Franklin Electric Industrial Equipment won’t start when demanding water?
- B
  bscottAug 27, 2025
  If your Franklin Electric Industrial Equipment unit won’t start with demand for water, it might be because the inlet water pressure is above 40 psi (2.8 bar). Install a pressure reducing valve on the inlet to reduce the inlet pressure, or wait for the inlet pressure to fall below 40 psi (2.8 bar).
T
tarajuarezAug 30, 2025
Why does my Franklin Electric Industrial Equipment run briefly but won’t develop pressure?
- A
  Ann AustinAug 30, 2025
  If your Franklin Electric Industrial Equipment unit runs briefly, won’t develop pressure, then turns off, the cause might be insufficient water or prime. Check water supply, valving, and priming sections of this manual for additional information.
P
Paul CantrellSep 1, 2025
Why Franklin Electric Water System continuously cycles ON/OFF?
- C
  cassandramorganSep 1, 2025
  If your Franklin Electric Water System experiences continuous ON/OFF cycling (rapid cycling), several factors could be responsible: 1. The pressure in the pressure tank may be improperly charged. In this case, set the pressure in the pressure tank to 2 psi lower than the cut-in pressure. 2. There may be a check valve issue between the tank and the unit. To resolve this, place the check valve after the pressure tank. 3. Leaks in the system plumbing or usage exceeding 0.5 gpm (1.9 lpm) could be the cause. Repair any plumbing leaks. 4. The internal non-return (check) valve might be blocked or damaged. Install a new non-return (check) valve before the unit in the inlet plumbing. 5. The internal flow piston could be stuck open. In this situation, clean the flow piston.
G
Gary GriffinSep 4, 2025
What to do if Franklin Electric Water System will not turn on?
- J
  Jennifer ChavezSep 4, 2025
  If your Franklin Electric Water System unit will not turn on, it might be due to a tripped or turned-off circuit breaker. Turn the circuit breaker on. It is also recommended to consult a licensed electrician to properly wire the Outlet/Junction Box.
D
David PorterSep 6, 2025
What to do if Franklin Electric Water System will not start with demand for water?
- E
  Elizabeth Cruz DVMSep 6, 2025
  If your Franklin Electric Water System unit will not start with a demand for water, it could be due to the inlet water pressure being above 40 psi (2.8 bar). To resolve this, install a pressure reducing valve on the inlet to reduce the inlet pressure, or wait for the inlet pressure to fall below 40 psi (2.8 bar).
U
uandersonSep 8, 2025
What to do if Franklin Electric Water System runs briefly, does not develop pressure, then turns off?
- A
  Alexis NortonSep 8, 2025
  If the Franklin Electric Water System unit runs briefly, fails to develop pressure, and then turns off, it may be due to insufficient water or prime. Check the water supply, valving, and priming.
D
danielsvincentSep 12, 2025
How to fix Dry Run Fault in Franklin Electric Water System?
- K
  Kelly BarrettSep 12, 2025
  If you are experiencing a Dry Run Fault with your Franklin Electric Water System, check the inlet water supply and valving. Also, ensure that the outlet pressure switch setting is not adjusted too high.