5-10
(H codes continued)
Code
Incre-
ment
Unit
Change
when
running
Data
copying
Default
setting
Refer to
page:
H54 0.01 s Y Y 6.00 -
H56 0.00 to 3600 0.01 s Y Y 6.00
H61
UP
/
DOWN
Control 0: 0.00
㧙㧙
NY 1
(Initial frequency setting) 1: Last
UP
/
DOWN
command value on releasing run command
H63 Low Limiter (Mode selection) 0:
㧙㧙
YY 0
1:
H64 (Lower limiting frequency) 0.1 Hz Y Y 1.6 -
H68 Slip Compensation 1 0: 㧙㧙 NY 05-37
(Operating conditions) 1:
2:
3:
H69 Automatic Deceleration 0: Disable 㧙㧙 YY 05-70
(Mode selection) 2:
4:
H70 Overload Prevention Control 0.01 Hz/s Y Y 999 5-71
H71 Deceleration Characteristics 0: Disable
㧙㧙
YY 0
1: Enable
H76 0.0 to 400.0 0.1 Hz Y Y 5.0 5-70
H80 0.00 to 0.40 0.01 㧙 Y Y 0.20 -
H89 Motor overload memory retention 0:Inactive
㧙㧙
YY 1
1:Active
H90 Reserved *2 0, 1
㧙㧙
YY 0
H91 0.1 s Y Y 0.0
H94 Cumulative Motor Run Time 1 Change or reset the cumulative data
㧙㧙
NN
㧙
5-71
H95 0: Slow
㧙㧙
YY 15-33
1: Quick
H96 Data STOP key priority Start check function
㧙㧙
YY 0 -
0: Disable Disable
1: Enable Disable
2: Disable Enable
3: Enable Enable
H97 Clear Alarm Data
㧙㧙
YN 05-70
H98
㧙㧙
Y Y 5-71
(Mode selection) Bit 0: Lower the carrier frequency automatically
Bit 1: Detect input phase loss
Bit 2: Detect output phase loss
Bit 4: Judge the life of DC link bus capacitor
0.0: Disable
0.1 to 60.0: Detection time
5-31
0.00 to 3600
*ACC time and DEC time are common.
Name
Deceleration Time for Forced Stop
0: Does not clear alarm data
1: Clear alarm data and return to zero
Enable (Canceled if actual deceleration time exceeds three times the
one specified by F08/E11.)
Enable (Not canceled if actual deceleration time exceeds three times the
one specified by F08/E11.)
Output Current Fluctuation Damping
Gain for Motor 1
STOP Key Priority/Start Check Function
Protection/Maintenance Function
DC Braking
(Braking response mode)
C1 Disconnection Detection Time
(PID control feedback line) *6
ACC/DEC Time
(Jogging operation)
If the output frequency lowers below the one limited by F16 (Frequency
limiter: Low), decelerate to stop the motor.
Bit 3: Select life judgment threshold of DC link bus capacitor
Data setting range
Torque Limiter (Frequency increment
limit for braking)
0.00 : Follow deceleration time specified by F08/E11
0.01 to 100.0
999: Disable
Disable during ACC/DEC and enable at base frequency or above
Enable during ACC/DEC and disable at base frequency or above
0.0 (Depends on F16 (Frequency limiter: Low))
0.1 to 60.0
Limit by F16 (Frequency limiter: Low) and continue to run
Enable during ACC/DEC and enable at base frequency or above
Disable during ACC/DEC and disable at base frequency or above
0 to 31: Display data on the keypad's LED monitor in decimal format
(In each bit, "0" for disabled, "1" for enabled.)
19
(bit4,
1,0
㧩
1)
A codes: Motor 2 Parameters
Code
Incre-
ment
Unit
Change
when
running
Data
copying
Default
setting
Refer to
page:
A01 Maximum Frequency 2 25.0 to 400.0 0.1 Hz N Y 60.0 -
A02 Base Frequency 2 25.0 to 400.0 0.1 Hz N Y 60.0
A03 0: 1 V N Y2
80 to 240: 230
160 to 500: 460
A04 Maximum Output Voltage 2 80 to 240V: 1 V N Y2 230
160 to 500V: 460
Output a voltage in proportion to input voltage
Output an AVR-controlled voltage (for 230 V class series)
Name Data setting range
Output an AVR-controlled voltage (for 460 V class series)
Output an AVR-controlled voltage (for 230 V class series)
Output an AVR-controlled voltage (for 460 V class series)
Rated Voltage at Base Frequency 2
*
2
These function codes and their data are displayed, but they are reserved for particular manufacturers. Unless otherwise
specified, do not access these function codes.
*
6
These are available on inverters with inverter's ROM version 0800 or later. (For the version checking procedure, refer to
Chapter 3, Section 3.4.6 "Reading maintenance information."
)
To Next Page
Loading...
