Fuji Electric FRENIC-Multi - Page 92

5-9
H codes: High Performance Functions
Code
Incre-
ment
Unit
Change
when
running
Data
copying
Default
setting
Refer
to
page:
H03 Data Initialization 0: Disable initialization
㧙㧙
NN 05-58
1:
2: Initialize motor 1 parameters
3: Initialize motor 2 parameters
H04 Auto-reset (Times) 1times Y Y 0
H05 (Reset interval) 0.5 to 20.0 0.1 s Y Y 5.0
H06 Coolin
g
Fan ON/OFF Control 0: Disable
(
Alwa
y
s in operation
)
㧙㧙
YY 05-64
1: Enable (ON/OFF controllable)
H07 0: Linear
㧙㧙
YY 0
1: S-curve (Weak)
2: S-curve (Strong)
3: Curvilinear
H08 0: Disable
㧙㧙
NY 0 -
1: Enable (Reverse rotation inhibited㧕
2: Enable (Forward rotation inhibited
㧕
H09 Starting Mode (Auto search) 0: Disable
㧙㧙
NY 05-65
1:
2:
H11 Deceleration Mode 0: Normal deceleration
㧙㧙
YY 05-67
1: Coast-to-stop
H12 0: Disable
㧙㧙
YY 1
Limiting 1: Enable
(Mode selection)
H13 0.1 to 10.0 0.1 s Y Y1
Y2
*4 5-28
H14 (Frequency fall rate) 0.00: Deceleration time selected by F08 0.01 Hz/s Y Y 999
H16
(
Allowable momentar
y
0.1 s Y Y 999
p
ower failure time
)
H26 0: Disable
㧙㧙
YY 0 -
1:
2:
H27
(
Level
)
0.00 to 5.00 0.01 V Y Y 1.60
H28 Droop Control -60.0 to 0.0 0.1 Hz Y Y 0.0 5-68
H30 Communications Link Function Run command
㧙㧙
YY 0
(
Mode selection
)
0: F02
1: F02
2: RS-485
3: RS-485
4: F02
5: RS-485
6: RS-485 (option)
7: RS-485 (option)
8: RS-485
(
option
)
H42 1
㧙
YN
㧙
-
H43
㧙㧙
YN
㧙
H44 Startup Times of Motor 1 Indication of cumulative startup times
㧙㧙
YN
㧙
H45 Mock Alarm 0:
1:
㧙㧙
YN 05-70
H47
㧙㧙
Y N Set at
factory
shipping
H48
㧙㧙
YN
㧙
H49 Starting Mode (Delay time) 0.0 to 10.0 0.1 s Y Y 0.0 5-65
H50 0.1 Hz N Y 0.0 5-21
H51 (Voltage) 1V N Y2 0
H52 0.1 Hz N Y 0.0
H53 (Voltage) 1V N Y2 0
-
5-63
Data setting range
Indication for replacing capacitors on printed circuit boards (0000 to FFFF:
Hexadecimal). Resettable.
Enable (With PTC, the inverter immediately trips with
displayed.)
F01/C30
Initialize all function code data to the factory defaults
Enable (At restart after momentary power failure and at normal start)
Enable (With PTC, the inverter issues output signal
THM
and
continues to run. *6
999 : Automaticall
y
determined b
y
inverter
Cumulative Run Time of Capacitors on
Printed Circuit Boards
Acceleration/Deceleration Pattern
Rotational Direction Limitation
Initial Capacitance of DC Link Bus
Capacitor
Name
Cumulative Run Time of Cooling Fan Indication of cumulative run time of cooling fan for replacement
Non-linear V/f Pattern 1
(Frequency)
Non-linear V/f Pattern 2
(Frequency)
Restart Mode after Momentary Power
Failure
ޓ(Restart time)
Thermistor (Mode selection)
Capacitance of DC Link Bus Capacitor Indication for replacing DC link bus capacitor (0000 to FFFF: Hexadecimal)
Enable (At restart after momentary power failure)
F01/C30
Indication for replacing DC link bus capacitor (0000 to FFFF: Hexadecimal)
Frequency command
RS-485
RS-485 (option)
RS-485 (option)
Instantaneous Overcurrent
0: Disable
1 to 10
0.01 to 100.00
999: Follow the current limit command
0.0 to 30.0
0.0 : Cancel
0.1 to 400.0
0 to 240 : Output an AVR-controlled voltage (for 200 V class series)
0 to 500 : Output an AVR-controlled voltage (for 400 V class series)
0.0 : Cancel
0.1 to 400.0
0 to 500: Output an AVR-controlled voltage (for 400 V class series)
RS-485
F01/C30
0 to 240: Output an AVR-controlled voltage (for 200 V class series)
RS-485
RS-485 (option)
Disable
Enable (Once a mock alarm occurs, the data automatically returns to
0.)
*
4
Default settings for these function codes vary depending on the inverter capacity. See Table 5.1 "Factory Defaults According
to Inverter Capacity" on pages 5-15 and 5-16.
*
6
These are available on inverters with inverter's ROM version 0800 or later. (For the version checking procedure, refer to
Chapter 3, Section 3.4.6 "Reading maintenance information."
J
)