Fuji Electric FRENIC-Multi - Page 97

5-14
y codes: Link Functions
Code
Incre-
ment
Unit
Change
when
running
Data
copying
Default
setting
Refer to
page:
y01 RS-485 Communication (Standard) 1 to 255 -
(Station address) 1
㧙
NY 1
y02 (Communications error processing) 0: Immediately trip with alarm
GT
㧙㧙
YY 0
1:
3: Continue to run
y03 (Timer) 0.0 to 60.0 0.1 s Y Y 2.0
y04 (Baud rate) 0: 2400 bps 㧙㧙 YY 3
1: 4800 bps
2: 9600 bps
3: 19200 bps
4: 38400 bps
y05 (Data length) 0: 8 bits
㧙㧙
YY 0
1: 7 bits
y06 (Parity check) 0: None (2 stop bits for Modbus RTU)
㧙㧙
YY 0
1: Even parity (1 stop bit for Modbus RTU)
2: Odd parity (1 stop bit for Modbus RTU)
3: None (1 stop bit for Modbus RTU)
y07 (Stop bits) 0: 2 bits
㧙㧙
YY 0
1: 1 bit
y08 (No-response error detection time) 0: No detection 1 s Y Y 0
1 to 60
y09 (Response interval) 0.00 to 1.00 0.01 s Y Y 0.01
y10 (Protocol selection) 0: Modbus RTU protocol 㧙㧙 YY 1
1: FRENIC Loader protocol (SX protocol)
2: Fuji general-purpose inverter protocol
y11 RS-485 Communication (Option) 1 to 255
(Station address) 1 㧙 NY 1
y12 (Communications error processing) 0: Immediately trip with alarm
GTR
㧙㧙
YY 0
1:
3: Continue to run
y13 (Timer) 0.0 to 60.0 0.1 s Y Y 2.0
y14 (Baud rate) 0: 2400 bps 㧙㧙 YY 3
1: 4800 bps
2: 9600 bps
3: 19200 bps
4: 38400 bps
y15 (Data length) 0: 8 bits
㧙㧙
YY 0
1: 7 bits
y16 (Parity check) 0: None (2 stop bits for Modbus RTU)
㧙㧙
YY 0
1: Even parity (1 stop bit for Modbus RTU)
2: Odd parity (1 stop bit for Modbus RTU)
3: None (1 stop bit for Modbus RTU)
y17 (Stop bits) 0: 2 bits
㧙㧙
YY 0
1: 1 bit
y18 (No-response error detection time) 0: No detection 1 s Y Y 0
1 to 60
y19 (Response interval) 0.00 to 1.00 0.01 s Y Y 0.01
y20 (Protocol selection) 0: Modbus RTU protocol 㧙㧙 YY 0
2: Fuji general-purpose inverter protocol
y98 Frequency command Run command
㧙㧙
YY 05-68
0: Follow H30 data Follow H30 data
1: Via field bus option Follow H30 data
2: Follow H30 data Via field bus option
3: Via field bus option Via field bus option
y99
ޓ
Frequency command Run command
㧙㧙
YN 0 -
0: Follow H30 and y98 data Follow H30 and y98 data
1: Via RS-485 link (Loader) Follow H30 and y98 data
2: Follow H30 and y98 data Via RS-485 link (Loader)
3: Via RS-485 link (Loader) Via RS-485 link (Loader)
Retry during the period specified by timer y03. If the retry fails, trip with
alarm
GT
. If it succeeds, continue to run.
Retry during the period specified by timer y13. If the retry fails, trip with
alarm
GTR
. If it succeeds, continue to run.
2:
2:
Trip with alarm
GTR
after running for the period specified by timer y13
Trip with alarm
GT
after running for the period specified by timer y03
Data setting range
Bus Link Function (Mode selection)
Loader Link Function (Mode selection)
Name