Heat Pump, Split System, Single Service, 3 phase
134 Maintenance Document 1394-1
12.3 Settings Sheet
Setting Description set to Menus Setting Description set to Menus
Preliminary settings Boiler backup
20 language
Op. section
3700 Release below out. temp
Suppl. source.
1 hour / minutes
time and date
3705 Overrun time
Suppl. source.
2 day / month
time and date
Miscellaneous
3 year
time and date
6046 Function Input H2 9
configuration
5700 Preselection
configuration
6100 Readjustm outside sensor
configuration
6120 Frost protect. for the plant
configuration
Heating circuit No. 1
if 2 circuits =less warmer one (e.g. floor)
6205 Reset to default param.
configuration
710 Comfort heating setpoint
Heat. circuit 1
6220 software version
configuration
712 Reduced setpoint
Heat. circuit 1
6711 Reset HP
errors
720 Heating curve slope
Heat. circuit 1
7070 to 7183 maintenance
Serv / special op.
750 Room influence
Heat. circuit 1
7700 to 7916 input/output testing
I/O test
790 / 791 Opt start/stop control max
Heat. circuit 1
8402 to 8457 generator diagnosis
Diagn. heat source
834 Acutuator running time
Heat. circuit 1
8700 to 9055 consumer diagnosis
Diagn.consumers
850 / 851 Floor curing
Heat. circuit 1
Cooling
501 to 516 time programs
HC1 time pgm
5711 Cooling circuit 1 2 pipes
configuration
642 to 648 holiday programs
Hol. HC1
901 to 969 cooling settings
cooling circuit 1
Heating circuit no. 2 (with 2nd circuit option)
= warmer one (e.g. radiators)
Faults
If a fault occurs, press "Info" key
1010 Comfort heating setpoint
Heat. circuit 2
No. 10 outdoor sensor
1012 Reduced setpoint
Heat. circuit 2
No. 33 flow temp sensor
1020 Heating curve slope
Heat. circuit 2
No. 44 return temp sensor
1050 Room influence
Heat. circuit 2
No. 50 DHW temp sensor
1090 / 1091 Opt start/stop control max
Heat. circuit 2
No. 60 room sensor 1
1134 Acutuator running time
Heat. circuit 2
No. 65 room sensor 2
1150 / 1151 Floor curing
Heat. circuit 2
No. 105 maintenance message
521 to 536 time programs
HC2 time pgm
No. 121 HC1 flow T not reached
652 to 658 holiday programs
Hol. HC2
No. 122 HC2 flow T not reached
Domestic Hot Water (if DHW kit) No. 127 Leg. prot. T not reached
1610 Nominal setpoint
DHW
No. 369 external fault (EX6)
1612 Reduced setpoint
DHW
No. 370 Outdoor unit connect error
1620 Release
DHW
6740 to 6746 alarm timeout
errors
1640 to 1647 Legionella cycle
DHW
6800 to 6818 last 10 alarms history
errors
1660 Circulation pump release
DHW
6711 reset HP
errors
5020 Flow setpoint boost
DHW stor. tank
Heat Pump
5024 Switching differential
DHW stor. tank
2844 Switch-off temp max
Heat pump
5030 Charging time limitation
DHW stor. tank
2884 Release el flowat OT
heat pump
5060 El imm heater optg mode fill
DHW stor. tank
2920
In case of peak day
clearing signal lock (EX4)
heat pump
5061 Elec imm. heater:release
DHW stor. tank
Swimming Pool (with"sw pool" kit option)
5870 Combi storage tank
configuration
2056 Setpoint source heating
sw pool
561 to 576 time programs
prog.4 DHW
Outdoor Unit Faults
Refer to "installation" instructions
To Next Page
Loading...
