Furuno FELCOM 500 - Service Manual

Other manuals for Furuno FELCOM 500

Questions and Answers:

G
Gerald EstradaAug 27, 2025
How to troubleshoot internal call issues on Furuno Boating Equipment?
- R
  Renee PadillaAug 27, 2025
  To resolve the issue of not being able to make internal calls on your Furuno Boating Equipment, take the following steps: * Check that the handset and/or analog phone cables are properly connected to the communication unit. * If using an analog phone, check the phone number in the Web software by navigating to Settings ? Basic settings ? Analog ports to ensure it is correct. * In the web software, go to Settings ? PBX settings ? Extension to verify that "Outside" or "Incoming" does not appear in the [Call limit] setting. * Confirm that the same extension number and password are entered in both the handset and web software. For the handset, go to Settings ? 3 SIP ? 1 Client set. In the web software, go to Settings ? PBX settings ? Extension.
W
williambutlerAug 27, 2025
What to do if Furuno Boating Equipment does not become [Ready] status?
- D
  David ThomasAug 27, 2025
  To resolve the issue of your Furuno Boating Equipment not reaching [Ready] status, check the following: * Ensure the antenna cable is properly connected. * Verify there are no obstructions blocking the signal between the antenna and the satellite. * Check if the ship position data is correct (if “No fix” or “No data” appears). * In the Web software, navigate to Main ? satellite search to perform a manual satellite search. * In the Web software, go to Settings ? Basic Settings ? GPS to confirm the backup GPS is configured correctly.
M
Mrs. Melissa KellyAug 25, 2025
Why nothing displays on the handset screen of my Furuno Boating Equipment?
- R
  rodney59Aug 26, 2025
  To resolve the issue of nothing displaying on the handset screen of your Furuno Boating Equipment, verify that the handset cable is properly connected to the communication unit and ensure the brightness level of the screen is not set too dark.

Furuno FELCOM 500 Specifications

General

Frequency Band	L-band
Data Rate	Up to 432 kbps
IP Handset	Yes
LAN Ports	2
Voice Support	Yes
SMS Support	Yes
Operating Temperature	-15°C to +55°C
Type	Inmarsat FleetBroadband Satellite Communication System
Communication Protocols	TCP/IP, SMTP, POP3
Antenna Type	Omnidirectional
Interface	Ethernet

Summary

Chapter 1. Overview

1.1 System Configuration

Details the system configuration and connected equipment, including optional units.

1.2 Overview of the Fleet Broad Band (FB)

Provides an overview of the Fleet Broad Band (FB) system, satellite coverage, and ground facilities.

1.3 Have the Web MMI for FELCOM-250;500 Displayed

Guides on accessing and displaying the Web MMI interface for system configuration and maintenance.

Chapter 2. Handling Password

2.1 SIM Password (PIN Code)

Explains how to manage SIM card PIN codes, including entry, blocking, and changes.

2.4 Handling the Password

Details password management across modes, lists passwords, and provides procedures for forgotten passwords.

Chapter 3. Menu Tree

3.1 Web MMI

Describes the structure and navigation of the Web MMI interface, including user authentication modes.

3.2 Handset

Details the structure and menu options of the Handset interface, including screen layouts.

Chapter 4. Settings for TEL;FAX

4.1 Overview

Provides an overview of TEL/FAX settings configuration on the Web MMI and Handset.

4.3 Registering the Handsets in the SIP Server (Mandatory)

Guides on registering Handsets in the SIP server for phone call functionality.

4.4 Setting the Incoming Routing (Mandatory)

Explains how to configure incoming call routes for Voice and FAX services.

Chapter 5. WAN Settings

5.1 WAN Settings

Details settings for Standard IP and Streaming IP data connections via WAN.

5.2 Diagnostics

Describes how to use Ping and Nslookup for confirming Internet connection status.

Chapter 6. UDI;RDI Communication

6.1 Overview

Explains ISDN UDI/RDI communication setup via serial port.

6.2 Settings

Guides on installing modems and configuring dial-up connections for UDI/RDI.

Chapter 8. Security Settings

8.1 Security Settings

Covers Firewall and IP Filter settings for network security and access control.

Chapter 9. Parts Location

9.1 Communication Unit: FB-2000

Identifies the front and rear panel components of the FB-2000 communication unit.

9.4 Antenna Unit: FB-1500

Details the components and internal structure of the FB-1500 antenna unit.

Chapter 10. Maintenance

10.1 Overview

Provides an overview of maintenance procedures and power-on sequences.

10.2 Status monitor

Explains how to monitor system status via Web MMI and Handset.

10.5 Selftest

Guides on executing self-tests for Antenna and Communication units.

10.9 Initializing

Details procedures for initializing the Communication unit and Handset.

Chapter 11. Block Description

11.1 Communication unit: FB-2000

Describes the block configuration and circuit diagrams of the FB-2000 communication unit.

11.2 Antenna unit: FB-1500;1250

Explains the overview, differences, and functions of the FB-1500/1250 antenna units.

Chapter 12. Updating the Software

12.1 Updating the Communication Unit Software

Guides on updating software for Communication units (HUB, MODEM).

12.3 BDE Software Updating Tool

Details the procedure for using the BDE software updating tool for various components.

Chapter 13. Q&A

Appendix 1. NMEA Port

AP1.1 Monitoring the GPS Data

Explains how to monitor GPS data from Internal or External GPS via Web MMI.

Appendix 3. Specifications

AP3.1 FELCOM-500

Lists the general, antenna, and communication unit specifications for FELCOM-500.

Appendix 4. Abbreviations

AP4-1 SIM Card (Subscriber Identity Module Card)

Defines SIM Card and related terms like PIN code, PUK code, IMEI, OTA.

AP4-5 PoE

Explains Power over Ethernet (PoE) technology and its classes.

Check List

1. Location of the Equipment

Instructions for describing the equipment's location and illustrating its surroundings.

2. The Settings and Operation Check

Details how to check system settings and operations by copying Web MMI information.

Summary

1. Installations

Covers power source requirements and antenna distance specifications.

2. Operations

Lists available services and communication rates for FELCOM-250/500.

4. Settings

Provides an overview of system configuration settings and examples.

Related product manuals

Furuno C-MAP NT GP-1650

94 pages

Furuno FELCOM 500 - Service Manual

Table of Contents

Other manuals for Furuno FELCOM 500

Questions and Answers:

Furuno FELCOM 500 Specifications

Summary

Chapter 1. Overview

1.1 System Configuration

1.2 Overview of the Fleet Broad Band (FB)

1.3 Have the Web MMI for FELCOM-250;500 Displayed

Chapter 2. Handling Password

2.1 SIM Password (PIN Code)

2.4 Handling the Password

Chapter 3. Menu Tree

3.1 Web MMI

3.2 Handset

Chapter 4. Settings for TEL;FAX

4.1 Overview

4.3 Registering the Handsets in the SIP Server (Mandatory)

4.4 Setting the Incoming Routing (Mandatory)

Chapter 5. WAN Settings

5.1 WAN Settings

5.2 Diagnostics

Chapter 6. UDI;RDI Communication

6.1 Overview

6.2 Settings

Chapter 8. Security Settings

8.1 Security Settings

Chapter 9. Parts Location

9.1 Communication Unit: FB-2000

9.4 Antenna Unit: FB-1500

Chapter 10. Maintenance

10.1 Overview

10.2 Status monitor

10.5 Selftest

10.9 Initializing

Chapter 11. Block Description

11.1 Communication unit: FB-2000

11.2 Antenna unit: FB-1500;1250

Chapter 12. Updating the Software

12.1 Updating the Communication Unit Software

12.3 BDE Software Updating Tool

Chapter 13. Q&A

Appendix 1. NMEA Port

AP1.1 Monitoring the GPS Data

Appendix 3. Specifications

AP3.1 FELCOM-500

Appendix 4. Abbreviations

AP4-1 SIM Card (Subscriber Identity Module Card)

AP4-5 PoE

Check List

1. Location of the Equipment

2. The Settings and Operation Check

Summary

1. Installations

2. Operations

4. Settings

Related product manuals