GE N60 - Page 641

GE Multilin N60 Network Stability and Synchrophasor Measurement System vii
INDEX
REPAIR .............................................................................H-7
REPLACEMENT MODULES ............................................. 2-11
REQUIREMENTS FOR INSTALLATION .............................. 1-5
RESET TO FACTORY DEFAULTS ...................................... 5-8
RESETTING ................................................. 5-8, 5-145, 5-231
to factory defaults............................................................ 5-8
REVISION HISTORY..........................................................H-1
RF IMMUNITY ................................................................. 2-22
RFI, CONDUCTED ........................................................... 2-22
RMS CURRENT ............................................................... 2-16
RMS VOLTAGE ............................................................... 2-16
ROLLING DEMAND ......................................................... 5-74
RS232
configuration ................................................................... 1-9
specifications ................................................................ 2-20
wiring............................................................................ 3-17
RS422
configuration ................................................................. 3-27
timing............................................................................ 3-29
two-channel application ................................................. 3-28
with fiber interface ......................................................... 3-29
RS485
description .................................................................... 3-19
specifications ................................................................ 2-20
RTD INPUTS
actual values ................................................................. 6-25
Modbus registers .................................................. B-24, B-36
settings ....................................................................... 5-244
specifications ................................................................ 2-17
S
SBO ................................................................................ 5-55
SELECT BEFORE OPERATE ........................................... 5-55
SELECTOR SWITCH
actual values ................................................................... 6-7
application example..................................................... 5-191
FlexLogic operands ..................................................... 5-142
logic............................................................................ 5-192
Modbus registers .................................................. B-51, B-52
settings ............................................................. 5-187, 5-211
specifications ................................................................ 2-15
timing................................................................ 5-190, 5-191
Self-test errors................................................................. 7-13
SELF-TESTS
description ...................................................................... 7-7
error messages ............................................................... 7-9
FlexLogic operands ..................................................... 5-146
Modbus registers .............................................................B-9
SENSITIVE DIRECTIONAL POWER
actual values ................................................................. 6-21
characteristic............................................................... 5-181
FlexLogic operands ..................................................... 5-140
logic............................................................................ 5-182
Modbus registers .................................................. B-16, B-40
settings ............................................................. 5-180, 5-182
specifications ................................................................ 2-13
SERIAL NUMBER ............................................................ 6-29
SERIAL PORTS
settings ......................................................................... 5-27
SETTING GROUPS................. 5-142, 5-162, 5-185, B-38, B-39
SETTINGS TEMPLATES
description.......................................................................4-4
editing .............................................................................4-4
enabling ..........................................................................4-4
Modbus registers .......................................................... B-78
password protection .........................................................4-5
removing .........................................................................4-7
viewing ............................................................................4-6
SETTINGS, CHANGING ...................................................4-26
SIGNAL LOSS DETECTION FOR FIBER ........................... 5-31
SIGNAL SOURCES
description.......................................................................5-6
metering ........................................................................6-16
settings ....................................................................... 5-103
SIGNAL TYPES..................................................................1-3
SINGLE LINE DIAGRAM.....................................................2-2
SITE LIST, CREATING .......................................................4-1
SNTP PROTOCOL
accuracy........................................................................2-20
error messages..............................................................7-10
Modbus registers ................................................. B-31, B-32
settings .........................................................................5-67
SOFTWARE
installation .......................................................................1-5
see entry for ENERVISTA UR SETUP
SOFTWARE ARCHITECTURE ............................................1-4
SOFTWARE, PC
see entry for EnerVista UR Setup
SOURCE FREQUENCY ....................................................6-20
SOURCE TRANSFER SCHEMES.................................... 5-174
SOURCES
description.......................................................................5-6
example use of ............................................................ 5-104
metering ........................................................................6-16
Modbus registers .......................................................... B-34
settings ....................................................................... 5-103
SPECIFICATIONS ............................................................2-13
STANDARD ABBREVIATIONS ........................................... H-5
STATUS INDICATORS ............................................ 4-14, 4-15
STORAGE TEMPERATURE .............................................. 2-21
SUB-HARMONIC STATOR GROUND FAULT
FlexLogic operands ...................................................... 5-143
SUMMATOR
actual values ................................................................. 6-22
FlexLogic operands ...................................................... 5-143
logic ............................................................................ 5-161
Modbus registers ................................................. B-45, B-51
settings ....................................................................... 5-159
SUPPORT, TECHNICAL .....................................................1-2
SURGE IMMUNITY...........................................................2-22
SYMMETRICAL COMPONENTS METERING .....................6-14
SYNCHROCHECK
actual values ............................................... 6-10, 6-21, 6-23
FlexLogic operands ...................................................... 5-143
logic ............................................................................ 5-198
Modbus registers ................................................. B-19, B-74
settings ............................................................ 5-195, 5-196
specifications.................................................................2-14
SYNCHROPHASORS
actual values ........................................................ 6-23, 6-24
clearing PMU records.......................................................7-2
commands ................................................................7-4, 7-5
FlexLogic operands ........................................... 5-141, 5-142
phase measurement unit triggering ............................... 5-124
phasor measurement configuration5-119, 5-120, 5-121, 5-122,