To Next Page

To Previous Page

Accessing the Camera

19.2.6 Alarm Notification

After input triggers and motion detection, you can be alerted by a pop-up

live video and view up to four captured images.

Pop-up live

video

Captured

images video

Figure 19-9

To configure this function, click the

Show System Menu button (No. 8,

Figure 19-3), and select

Alarm Notify. This dialog box appears.

Figure 19-10

 Motion Notify: Once motion is detected, the captured images are

displayed on the control panel of the Live View window.

273

Default Chapter12
- Table of Contents12
- Naming and Definition23
- Device Description24
- Options24
- Note for Connecting to GV-System27
- Note for Recording28
- Note for Adjusting Focus and Zoom29
- Note for Installing Camera Outdoor30
- Note for Closing the Bullet Camera Cover32
- Note for USB Storage and Wifi Adapter33
Chapter 1 Introduction34
- System Requirement34
Chapter 2 Box Camera35
- Specifications37
- Packing List39
- Features40
  - Wide Dynamic Range Pro42
  - For GV-Ipcam H.264 Models that Support WDR, the WDR Effect Is Achieved through Software Programming42
- Overview43
- Accessory Installation51
  - C-Mount Lenses51
  - Infrared Illuminators (Optional)52
- I/O Terminal Block53
  - Pin Assignment53
  - Connecting to GV-Relay V2 (Optional)54
Chapter 3 Ultra Box Camera55
- Packing List56
- Features57
- Overview58
- Installation59
- Connecting the Camera61
Chapter 4 Target Box Camera62
- Packing List62
- Features63
- Overview64
- Installation65
- Connecting the Camera67
Chapter 5 IR Arctic Box Camera68
- Packing List69
- Features70
- Overview72
- Installation73
- Connecting the Camera77
- Wire Definition77
- Notice for Using the IR Arctic Box Camera79
- Enabling IR LED after Loading Default79
  - Disabling Status LED under Low Light Conditions80
Chapter 6 Mini Fixed Dome & Mini Fixed Rugged Dome81
- Packing List84
- Features85
- Overview88
- Installation95
  - GV-MFD Series95
  - GV-MDR Series97
- Connecting the Camera102
Chapter 7 Target Mini Fixed Dome105
- Packing List105
- Features106
- Overview107
- Installation108
- Connecting the Camera111
Chapter 8 Bullet Camera112
- Packing List114
- Features115
- Overview117
- Installation118
Chapter 9 Ultra Bullet Camera132
- Packing List134
- Features135
- Overview137
- Installation139
  - Connecting the Camera142
  - Waterproofing the Cable145
Chapter 10 Target Bullet Camera148
- Packing List148
- Features149
- Overview150
- Installation152
- Connecting the Camera155
Chapter 11 PTZ Camera157
- Packing List158
- Features159
- Overview160
- Installation162
- PTZ Control171
Chapter 12 PT Camera187
- Packing List187
- Features189
- Overview190
- Installation192
- Connecting the Camera192
- Focus Adjustment192
- I/O Terminal Block193
  - Pin Assignment193
  - Voltage Load Expansion (Optional)193
- PT Control194
Chapter 13 Vandal Proof IP Dome (Part I)196
- Packing List198
- Features199
- Overview201
- Installation203
Chapter 14 Vandal Proof IP Dome (Part II)214
- Packing List216
- Features219
- Overview221
- Installation223
- Connecting the Camera233
Chapter 15 Fixed IP Dome235
- Packing List237
  - Packing List for Hard-Ceiling Mount237
  - Packing List for In-Ceiling Mount238
- Features239
- Overview241
- Installation243
- Connecting the Camera253
- I/O Terminal Block254
- Pin Assignment254
- Voltage Load Expansion (Optional)255
Chapter 16 Cube Camera256
- Packing List257
Chapter 17 Advanced Cube Camera263
- Packing List264
- Features265
- Overview266
- Installation268
- Connecting the Camera270
Chapter 18 Getting Started271
- Accessing the Live View271
- Adjusting Image Clarity281
  - Using Focus Adjustment Cap284
  - Locations of Adjustment Screws285
- Configuring the Basics287
Chapter 19 Accessing the Camera288
- Accessing Your Surveillance Images289
- Functions Featured on the Main Page290
Chapter 20 Administrator Mode319
- Video and Motion322
- I/O Settings341
- Events and Alerts346
- Monitoring364
  - Monitoring Settings for Target Series365
- Recording Schedule366
  - Recording Schedule Settings366
  - I/O Monitoring Settings367
- Remote Viewlog368
- Network369
- Management380
Chapter 21 Recording and Playback394
- Recording394
- Playback395
Chapter 22 Advanced Applications404
- Upgrading System Firmware404
  - Using the Web Configuration Interface406
  - Using the IP Device Utility407
- Backing up and Restoring Settings409
- Restoring to Factory Default Settings411
- Verifying Watermark423
- Downloading Videos from the Micro SD Card426
  - Installing the GV-Sdcardsync Utility427
  - The GV-Sdcardsync Utility Window431
Chapter 23 DVR Configurations433
- Setting up an IP Camera440
  - Customizing IP Camera Settings443
- Remote Monitoring with Multi View445
  - Connecting to the IP Camera445
- Remote Monitoring with E-Map446
  - Creating an E-Map for the IP Camera446
  - Connecting to the IP Camera448
Chapter 24 CMS Configurations449
- Center V2449
- Vsm452
- Dispatch Server453
Chapter 25 Smart Device Connection455
Appendix456
- Settings for Internet Explorer 8456
- Supported Lenses for Box Camera457
- Resolution and Frame Rate458
- Support Lists464
- RTSP Protocol Command470
- The CGI Command471
- Dual Stream Support List473
- Power Supply Support List476
- Supported Firmware for Flash Memory477
- Specifications478

Brand	GeoVision
Model	GV-FD120D
Category	Security Camera
Language	English

GeoVision GV-FD120D User Manual

Table of Contents

Other manuals for GeoVision GV-FD120D

Questions and Answers:

GeoVision GV-FD120D Specifications

Related product manuals