What to do if Getinge Maquet SERVO-i Medical Equipment panel button is stuck?
If the panel button on your Getinge Medical Equipment is stuck, try the following: * Restart the unit, avoiding any contact with the User Interface during startup. * Verify that System SW V1.03.00 (or later) is installed, and update if necessary. * Check the user interface membrane buttons (FSS). * Replace the touch screen. * Replace PC 1777 Panel.
What to do if Getinge Maquet SERVO-i safe valve is open?
If the safe valve is open on your Getinge Medical Equipment, you should: * Check inspiratory channel. * Replace safety valve pull magnet. * Replace PC 1784 Expiratory channel.
What to do if Getinge Medical Equipment panel audio failed?
If the panel audio on your Getinge Medical Equipment has failed, you can try: * Restarting the unit, making sure not to touch the User Interface during system start-up. * Checking that System SW V1.03.00 (or later) is installed and update System SW if required. * Replacing the loudspeaker. * Replacing PC 1777 Panel.
What to do if Getinge Maquet SERVO-i Medical Equipment shows INSP_VALVE_RANGE_ERR?
If your Getinge Medical Equipment displays the error INSP_VALVE_RANGE_ERR, you can try: * Replacing PC 1771 Control. * Replacing PC 1772 Monitoring. * Replacing the gas modules one at a time, checking after each replacement to see if the error code disappears.
What to do if Getinge Maquet SERVO-i shows POWER_FAILURE_24_VOLTS_TOO_LOW?
If your Getinge Medical Equipment shows a POWER_FAILURE_24_VOLTS_TOO_LOW error, you should: * Replace PC 1778 DC/DC & Standard Connectors. * Replace the gas modules. Replace one gas module at a time and check that this technical error code will not appear.
What to do if Getinge Maquet SERVO-i shows POWER_FAILURE_12_VOLTS_TOO_LOW?
If your Getinge Medical Equipment displays a POWER_FAILURE_12_VOLTS_TOO_LOW error, you can try the following: * Check the status of the external battery (if connected). * Replace PC 1778 DC/DC & Standard Connectors. * Replace PC 1775 Plug-and-play back-plane.
What to do if Getinge Medical Equipment shows POWER_FAILURE_MINUS_12_VOLTS_TOO_HIGH?
If your Getinge Medical Equipment displays a POWER_FAILURE_MINUS_12_VOLTS_TOO_HIGH error, you can try: * Checking the status of the external battery (if connected). * Replacing PC 1778 DC/DC & Standard Connectors. * Replacing PC 1775 Plug-and-play back-plane.
What to do if Getinge Maquet SERVO-i shows POWER_FAILURE_24_VOLTS_TOO_HIGH?
If your Getinge Medical Equipment shows a POWER_FAILURE_24_VOLTS_TOO_HIGH error, replace PC 1778 DC/DC & Standard Connectors.
What to do if Getinge Maquet SERVO-i shows POWER_FAILURE_12_VOLTS_TOO_HIGH?
If your Getinge Medical Equipment shows a POWER_FAILURE_12_VOLTS_TOO_HIGH error, replace PC 1778 DC/DC & Standard Connectors.
What to do if Getinge Maquet SERVO-i Medical Equipment shows POWER_FAILURE_MINUS_12_VOLTS_TOO_LOW?
If your Getinge Medical Equipment displays the error POWER_FAILURE_MINUS_12_VOLTS_TOO_LOW (i.e. < -13.2 V), replace PC 1778 DC/DC & Standard Connectors.
Provides an overview of the manual's scope and applicability to SERVO-i/s systems.
Discusses variations in cleaning practices and Maquet's recommendations.
Explains the meaning of various symbols used throughout the manual.
Defines different types of information alerts to ensure safe operation.
Offers a concise overview of cleaning and disinfection steps for the equipment.
Details the steps for preparing and taking apart the equipment for cleaning.
Outlines procedures for wiping down equipment and properly disposing of parts.
Explains various methods for disinfecting the equipment components.
Discusses sterilization methods, noting they are generally not recommended.
Provides instructions on how to reassemble the equipment after cleaning.
Details the cleaning process specific to the SERVO Ultra Nebulizer.
Covers the cleaning procedures for the Aerogen Pro Nebulizer.
Explains how to clean the SERVO-i NAVA system components.
Provides instructions for cleaning the SERVO CO2 analyzer.
Refers to cleaning routines for associated accessories.
Outlines recommendations for regular equipment inspection and maintenance.
Details maintenance requirements and notes for the O2 sensor.
Covers the replacement procedure and safety warnings for the O2 cell.
Provides instructions for advanced cleaning of the inspiratory channel.
Refers to maintenance procedures for associated accessories.
General| Brand | Getinge |
|---|---|
| Model | Maquet SERVO-i |
| Category | Medical Equipment |
| Language | English |
To Next Page
