Why does the Graco Project Paint Sprayer Spray Tip continue to drip after releasing the trigger?
If the spray tip of your Graco Paint Sprayer continues to drip or ooze material after releasing the trigger: * The spray tip may be worn and need replacement. * The spray tip may not be fully inserted into the spray tip guard.
What to do if my Graco Paint Sprayer's spray pattern is dripping or sagging?
If you're experiencing dripping or sagging in your Graco Paint Sprayer's spray pattern: * Move the sprayer faster while spraying. * Move the sprayer away from the surface. * Release the trigger when changing directions. * Decrease the speed control if it is set too high. * Replace the spray tip if it is worn or damaged.
How to eliminate tails in the spray pattern of my Graco Project Paint Sprayer?
If your Graco Paint Sprayer's spray pattern has tails, try the following: * Increase the speed control if it's set too low. * Install a different size spray tip. * Thin the material according to the paint manufacturer's recommendations. * Change to a different material if the current one is not compatible with the sprayer. * Replace the spray tip if it is worn or damaged.
How to clean a plugged pump filter on Graco Project Paint Sprayer?
To clean a plugged pump filter on your Graco Paint Sprayer, remove the pump filter from the pump and clean both sides. While the filter is removed, inspect the pump inlet for dried paint debris.
Why does my Graco Project spray pattern “spit” at the end or beginning?
If your Graco Paint Sprayer's spray pattern "spits" at the end or beginning, this could be due to: * Excess material accumulated on the Spray Tip and Spray Tip Guard, or the Spray Tip is partially plugged; clean the Spray Tip and Spray Tip Guard, and clear the Spray Tip. * The Spray Tip is not fully inserted into the Spray Tip Guard. * The Spray Tip is worn or damaged; replace it. * The pump has reached its maximum life; replace the pump.
Why does my Graco Paint Sprayer spray pattern spit at the end or beginning?
If your Graco Paint Sprayer's spray pattern spits at the end or beginning, it could be due to: * Excess material on the spray tip and guard, or a partially plugged tip; clean the spray tip and guard, and clear any clogs. * The spray tip not being fully inserted into the spray tip guard. * A worn or damaged spray tip; replace it. * The pump has reached its maximum life; replace the pump.
How to fix a Graco Project Paint Sprayer that sprays with poor results?
If your Graco Paint Sprayer is spraying with poor results, consider these possibilities: * The spray tip may be partially clogged. * The spray tip may not be in the correct position. * The spray tip may be worn or damaged. * The material being sprayed is aerated or too cold. Also, make sure that the outlet valves are clean and properly installed. If the issue persists, the pump assembly may need to be replaced. Ensure you are using the correct spray tip for the material.
What to do if Graco Project Paint Sprayer is not primed?
If your Graco Paint Sprayer isn't primed, repeat the start-up procedure to remove air from the FlexLiner. Verify the cup lid is tight, using seal lube on the gasket for an airtight seal. If it sprays upside down but not upright, there's likely an air leak; replace the FlexLiner and VacuValve. Ensure only one FlexLiner is in the cup support and that there's no damage or debris on the FlexLiner's sealing edge or cup lid gasket. Make sure all air is out of the FlexLiner and the VacuValve cap is closed, and that the cup assembly is correctly installed. Clean the sprayer.
Why does my Graco Project Paint Sprayer spray pattern 'spit' at the end or beginning?
If your Graco Paint Sprayer's spray pattern 'spits', it could be due to excess material on the spray tip and guard, or a partially plugged tip, so clean the spray tip and guard, and clear the tip. Ensure the spray tip is fully inserted into the spray tip guard. A worn or damaged spray tip will cause this, so replace it. It's also possible the pump has reached its maximum life, so replace the pump. Finally, check if the extension spring has fallen out of place and put it back.
Provides crucial medical alert information for injection injuries.
Emphasizes reading and practicing safety habits before operation.
Lists available sprayer models with specifications and certifications.
Details mandatory grounding procedures to prevent electric shock.
Guidelines for selecting and using appropriate extension cords.
Covers risks associated with flammable materials and ignition sources.
Highlights dangers of improper grounding, setup, or usage.
Warns about high-pressure spray injection risks and necessary precautions.
Addresses risks from improper operation, fatigue, or alterations.
Warns against incompatible fluids causing reactions with aluminum parts.
Alerts to risks from toxic fluids or fumes via skin contact or inhalation.
Recommends appropriate protective gear for safe operation in the work area.
Explains the function of the Prime Knob for purging air and spraying fluid.
Describes the VacuValve's role in evacuating air from the FlexLiner for priming.
Details the Spray Tip's importance in airless spraying and its reversible function.
Explains how the Speed Control adjusts sprayer output for different patterns.
Step-by-step guide to safely relieve system pressure before maintenance or transport.
Instructions for preparing the sprayer, including FlexLiner and cup assembly.
Recommends spray tip sizes and types for various coatings and speed control settings.
Guides on adjusting the spray tip guard for horizontal or vertical spray direction.
Advice on achieving an even spray pattern by adjusting settings and technique.
Instructions on holding the sprayer at the correct angle for an even finish.
Technique for overlapping spray strokes for consistent coverage.
Explains the proper timing for pulling and releasing the trigger during spraying.
Information on compatible wide and narrow reversible spray tips and filter use.
Procedure for clearing a clogged spray tip using the reversible tip function.
Step-by-step guide for correctly installing the spray tip and guard.
Instructions on how to refill the cup and re-install the pump filter.
Steps to follow when pausing spraying to prevent drying and clogs.
Detailed instructions for cleaning the sprayer after use to ensure longevity.
Guidance on flushing the system with water for water-based materials.
Procedure for cleaning outlet valve assemblies to restore performance.
Guidance on dismantling and recycling the product responsibly.
Procedures for dismantling and disposing of the pump if it's no longer operational.
Table for diagnosing sprayer issues based on diagnostic light indicators.
Guide to identifying and resolving common spray pattern problems.
Comprehensive list of replacement parts with part numbers and descriptions.
General| Brand | Graco |
|---|---|
| Model | Project Series |
| Category | Paint Sprayer |
| Language | English |
To Next Page