What to do if GRAPHTEC FC8600-130 Plotter registration marks cannot be scanned?
If registration marks cannot be scanned properly on your Graphtec Plotter because of scan errors, and the cutting media is floating, press down the cutting media.
Why does my GRAPHTEC Plotter tool move up and down so much?
If your Graphtec Plotter has too many tool up and down movements, the setting for the tangential mode is set to ON. Turn OFF the setting for the tangential mode unless you are cutting thick media.
What causes 'POSITION ALARM' on my GRAPHTEC FC8600-130?
If the Graphtec Plotter stops with "POSITION ALARM" during initialization or cutting, it may be caused by movement being disturbed by media chaff in the operation area. Remove the object disturbing the operation, and turn the plotter on again after turning it off.
Why are characters deformed when pen plotting on my GRAPHTEC FC8600-130?
If characters or lines are deformed during pen plotting on your Graphtec Plotter, the plotter is in cutting mode. Select PEN as the tool in the CONDITION setting.
Why does my GRAPHTEC Plotter cut crooked lines?
If the Graphtec Plotter cut line starts out crooked, the blade mounted in the tool holder does not rotate smoothly. Remove any foreign matter inside the holder.
How to fix a GRAPHTEC FC8600-130 when no lights are on?
Check that the power cord is securely connected to the plotter's AC line inlet and the electrical outlet. Check that the power is supplied to the electrical outlet. Contact your Graphtec call center if the problem still exists.
What to do if GRAPHTEC FC8600-130 Plotter keeps dropping media?
If the Graphtec Plotter drops the media while detecting, the media sensor may be defective. Contact your sales representative or the Graphtec call center. Set the media sensor to DISABLED to use the plotter temporarily.
How to fix blade skipping issues on GRAPHTEC Plotter?
If the Graphtec Plotter blade skips and does not completely cut lines that should be solid, and straight cut lines seem to wobble, and the blade is extended too far, adjust the blade length.
How to adjust quality settings to prevent media curling on GRAPHTEC FC8600-130 Plotter?
If the Graphtec Plotter media curls up at the corners and fine cut characters peel off, and the QUALITY setting is too high, lower the QUALITY setting.
How to resolve scan errors with registration marks on GRAPHTEC FC8600-130?
If registration marks cannot be scanned properly on your Graphtec Plotter because of scan errors, and there are smears within the scanning area, remove the smears.
Highlights the sharpness of blades and pens, and the need for careful handling to prevent injury.
Covers cutter pen nomenclature, structure, and blade length adjustment for optimal cutting.
Explains the process for loading roll and sheet media using rear or front loading methods.
Covers setting and managing tool conditions like force, speed, quality, and offset for different media.
Guides on performing test cuts to optimize cutting parameters and confirm results before actual cutting.
Details how to set the cutting origin point at any location on the media for precise starting positions.
Explains the cross-cut function for cutting off media, manually or automatically, and adjusting cross-cut force.
Explains the COPY function to cut multiple copies of data stored in the buffer memory.
Introduces ARMS, its function for scanning registration marks, and its accuracy specifications.
Covers configuring ARMS settings like scan mode, mark type, distance, sensor level, and testing.
Explains methods to adjust cutting position using ARMS based on 2, 3, or 4 registration marks for precision.
Details the procedure for automatic registration mark scanning and position adjustment via ARMS.
Describes the manual process for adjusting position by moving the tool to scan registration marks.
Provides methods for manual position adjustment, including axis alignment and light pointer usage.
Explains Tangential Mode for precise corner cutting, including overcut settings and control methods.
Explains how to correct length deviations by specifying a percentage-based DISTANCE ADJUST value.
Allows setting perforated or solid cut lines, with options for user-defined patterns and UP MODE.
Enhances cutting efficiency by sorting data (area or tool) to minimize media movement and tool exchange.
Covers configuration of USB, Network (LAN), and RS-232C interfaces for plotter communication.
Outlines routine cleaning and care for the plotter's components, including casing, mat, and sensors.
Details the step-by-step process for replacing the cutter blade in the cutter pen for optimal cutting.
Explains how to replace the cross cut unit, emphasizing safety due to the sharp blade.
Addresses issues where the plotter does not turn on or respond, listing symptoms, causes, and solutions.
Provides troubleshooting steps for common operational errors like media handling, carriage movement, and origin point issues.
Offers solutions for problems related to scanning registration marks, such as thin lines, smears, or media issues.
Lists causes and solutions for unsatisfactory cutting outcomes, including blade, offset, speed, and force settings.
Details error messages specific to GP-GL command mode, their causes, and how to resolve them.
Lists HP-GL command mode error messages, common causes related to software/interface configuration, and solutions.
Provides a reference for ARMS-related error messages, their causes, and corrective actions.
Guides on performing a self-diagnostic test on sensors and switches immediately after powering on the plotter.
Details how to access and view stored error messages for troubleshooting purposes.
Details how to adjust tool offset values to compensate for cutting differences between multiple tools.
Lists key technical specifications for the FC8600 series plotters, including dimensions, speed, and power requirements.
To Next Page
General