154
Basic settings
Basic transmitter settings
In this menu you can adjust and enter the basic gene-
ral settings which refer to the transmitter overall, e. g.
the owner’s name, but also pre-sets for newly set-up
model memories.
Select the relevant line with the rotary control pressed
in, then press the rotary control briefl y.
The presets …
• “Stick mode”,
• “Modulation”,
• “Collective pitch min.”
… which you set in this menu are automatically ad-
opted in any “free” model memory when you initiali-
se it, i. e. use it for the fi rst time. However, these set-
tings can be changed subsequently using the follo-
wing menus: »Base setup model« and »Helicopter
type«. Changes to the “presets” in this menu there-
fore only affect model memories which you initialise in
the future.
Note:
The settings you enter in this menu are only entered
once, and apply to the whole of the transmitter. When
a model memory is initialised, the current settings in
this menu are adopted in that memory.
Owner’s name
At this point you can enter a name with a maximum
of 15 characters. Hold the rotary control pressed in to
switch to the next screen page () …
<H-J Sandbru
n
!“#$%&´( )*+,-./0123456789:;<=>?
@ABCDEFGHIJKLMNOPQRSTUVWXYZ[¥]^_
`abcdefghijklmnopqrstuvwxyz{}~
n
c
N
ÇüéâäàåçêëèïîìÄÅÉæÆôöòûùÿÖÜ
n
–
>
Owners name
… where you can enter the owner’s name by selec-
ting letters from the character list. Use the rotary con-
trol to select the character or symbol, and press the
rotary control briefl y (or press and turn it) to accept
the chosen character and move on to the next positi-
on. You can move to each character within the name
by holding the rotary control pressed in; (the screen
shows a double arrow “<-->” at the appropriate posi-
tion). Pressing CLEAR inserts a space character at
that point.
Preset stick mode
Basically there are four possible ways of arranging
the principal control functions on the two dual-axis
sticks: the primary functions are aileron, elevator, rud-
der and throttle (or airbrakes) for a fi xed-wing model,
and roll, pitch-axis, tail rotor and throttle / collective
pitch on a model helicopter. Which of these possible
options you select depends on your individual prefe-
rences and fl ying style.
At the bottom edge of the screen you will see SEL.
Press the rotary control briefl y, then select one of the
options 1 to 4. Pressing CLEAR resets the function to
stick mode “1”.
Note:
In the fi xed-wing program the direction of effect of the
C1 stick can be changed individually in the »Model
type« menu.
Fixed-wing stick modes
Helicopter stick modes
154
Program description:
Global functions
GENERAL BASIC SETTINGS
Owners name
Pre-set stick mode
Pre-set modulation
Power-on beep
Battery warning
Own phase name
Pre-set min. pitch
1
SPCM20
yes
9.3V
forwrd
Display light unlim.
<
1< >
2< >
3
<>
4< >
5< >
6< >
7< >
8
<>
9 <>
10 < >
>
Own phase name
Own phase name
Own phase name
Own phase name
Own phase name
Own phase name
Own phase name
Own phase name
Own phase name
Full-throttle
Rudder
Rudder
Motor idle
Down-elevator
Up-elevator
Aileron
Aileron
Down-elevator
Up-elevator
Rudder
Rudder
Full-throttle
Motor idle
Aileron
Aileron
»MODE 1«
(Throttle right)
»MODE 2«
(Throttle left)
Full-throttle
Aileron
Aileron
Motor idle
Down-elevator
Up-elevator
Rudder
Rudder
Down-elevator
Up-elevator
Aileron
Aileron
Full-throttle
Motor idle
Rudder
Rudder
»MODE 3«
(Throttle right)
»MODE 4«
(Throttle left)
min. Pitch
Tail rotor
Tail rotor
max. Pitch
Pitch-axis
Pitch-axis
Roll
Roll
Pitch-axis
Pitch-axis
Tail rotor
Tail rotor
min. Pitch
max. Pitch
Roll
Roll
»MODE 1«
(Pitch right)
»MODE 2«
(Pitch left)
To Next Page
Loading...
