Hawk Gladiator - Specifications

39
Specications
Gladiator Gen 3 Microwave Series
Operating Voltage
• Integral 12-30VDC / Remote 12-30VDC
(residual ripple no greater than 100mV)
• Integral 80-260VAC / Remote 90-260VAC 50 / 60Hz.
• Remote 36-60VDC
Power Consumption
• <0.8W @ 24VDC • <3VA @ 115VAC
• <6W @ 48VDC • <5VA @ 240VAC
Communications
• GosHawk, Modbus • 4-20mA
• Multidrop mode can address 1-250 units over 4 wires.
Relay Output: (1) SMART (2) Remote
• Form ‘C’ (SPDT) contacts, rated 5A at 240VAC resistive
• Remote fail-safe test facility for one relay.
Operating Temperature
• Remote electronics -40°C (-40°F) to 80°C (176°F)
• Integral Units -30°C (-20°F) to 65°C (150°F)*
• Remote Sensors -30°C (-20°F) to 65°C (150°F)*.
*For higher temperature applications, remote mounting
with refractory windows is necessary.
Power Density
• Rated from emitter to receiver at approximately 20µW/cm²
• Complies with FCC Title Rules Part 15 (Beam Blockage)
• Caution sign posting not required.
Transmitted Signal
• Circular transmission polarity
• Frequency: 10.525GHz • Sensitivity -95dBm
• Power: +20dBm/100mW • Beam width 25º
Fail-Safe
• Selectable - presence or absence of material
• High level fail-safe:
relay is activated when material is present
• Low level fail-safe:
relay is activated when no material is present.
Range
• Maximum range under ideal conditions: 1200m (656ft)
• Minimum range under ideal conditions: 10cm (4 inches).
Note: Minimum ranges are dependent on application
conductivity.
Sender/ReceivertoAmplierSeparation
• Up to 500m (1640ft) using specified extension cable.
AlternatecabletypebetweenAmplierandSensors
• 6 or 8 conductor (5 used) shielded twisted pair
instrument cable
• Conductor size dependent on cable length
• BELDEN 3120A, DEKORON or equivalent
• Max: BELDEN 3120A = 500m (1640 ft). 3 pairs,
1 conductor not used
• Max: DEKORON IED183AA004 = 350m (1150 ft).
4 pairs, 3 conductors not used.
Maximum Operating Pressure
• 2 BAR
Display (Remote version only)
• 2 line x 12 character alphanumeric LCD
• Backlight standard.
Memory - Remote
• Non-Volatile (No backup battery required)
• >10 years data retention.
Enclosure Sealing
• Integral Sensors IP66/67 • Remote Sensors IP66/67
• Remote Electronics IP65 (NEMA 4x).
Cable Entries
• Remote Sensors:
1xM20 Gland / 3/4” NPTF threaded adaptor
• Remote Amplifier: 4x20mm (0.8”), 1x16mm (0.6”) knock outs
• Integral Units: 2xM20 Glands / 3/4” NPTF threaded adaptors.
Mounting
• 3” male NPT thread or four 10mm (0.4”) holes in flange
• MA12 / MA13 adjustable mounting bracket
Environment Seal
• 3”, 4” and 6” weldments for standard mounting on
vessel wall with PTFE and UHMW windows
• Flange for mounting separate from vessel wall -
isolation shock mounts are available
• Ceramic window assemblies
• Firebrick window assemblies available on custom basis
• Waveguides - custom assemblies available for high
temperature and limited access applications.
Weight
• GSA 1kg • GMS 5kg • GMR 5kg
Approval
• IECEx Zone 20/21, Zone 21
• Ex ta tb IIIC T* Da Db Tamb -30°C to +80°C / Tamb = -30°C
to +55°C (model dependent)
• IP66
*Consult Safety Instructions