EasyManuals Logo

Heathkit HW-9 User Manual

Heathkit HW-9
146 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #42 background imageLoading...
Page #42 background image
Page
42
Heathkit*
3
Refer
to Part
B of the
Detail
and
push
one
end of
the black
wire
through
the
bead
until it
extends
1"
from
the
bead
and is next
to one
end of
the violet
wire.
Then wind
three
turns
of wire
around
the
bead
so they
are between
the
turns
of
the violet
wire.
Ins
4
Refer
again
to Part
B of the
Detail
and
cut off
the excess
ends
of wire
so they
extend
1/2"
away
from
where
they
exit
the
core. Then
remove
1/4"
of
insulation
from
each
wire
end.
( )
T402:
Install
the
prepared
transformer
in the
circuit
board at T402.
Be
sure
the black
wires
go into
circuit
board holes
3 and
4
and the
violet
wires
go
into
holes 1
and 2.
Then
posi-
tion
the
transformer
down
against
the
circuit
board
and
solder
the wires
to the foil.
Cut off
any
excess wire
lengths.
NOTE
an
and
leads.
One
lead
will
have
a positive
(
+
)
mark
or
a negative
(-)
mark
near
it. Be
sure
to install
the
positive
lead in
the
positive-marked
hole,
or the
negative
lead
in
the
negative-marked
hole.
NEGATIVE
<-)
MARK
POSITIVE
WO
MARK
(
)
C436: 10 |xF,
35 V electrolytic
capacitor. Be
sure to observe
the correct
polarity.
NOTE:
Electrolytic
capacitors are
identified
on the
circuit
board by the following
outline:
POLARITY
MARKING
OUTLINE
OWS.
ns
cui
all parts
in Section 2
of the circuit board as fol-
R333:
2000
(2
k] (I
control (#10-318).
R445:
50 kft
control (#10-222).
C444:
330
jxF
electrolytic
capacitor.
C578:
47 \xJ?
electrolytic
capacitor.
C571:
.68 \lF
electrolytic
capacitor.
C572:
.68
jxF
electrolytic
capacitor.
C435:
2.2 \l¥
electrolytic
capacitor.
C427:
10 jxF,
35 V
electrolytic
capacitor.
C514:
1.5 jxF
electrolytic
capacitor.
Solder the
leads to
the
foil and cut
off the
ex-
cess
leads
lengths.
all
electrolytic
capacitors
in Section 3
of the
cir-
board as
follows.
C346: 2.2 jxF.
C343:22 \xF.
C347:
2.2
jjlF.
C342: 100 *jlF.
C575: .68 ^F.
C577: 22
p.F.
C317:3.3^jlF.
C576: 3.3
p,F.
Solder the leads
to the
foil and
cut off the
ex-
cess lead lengths.
(
)
Solder the
leads to the
foil and
cut
off the ex
cess lead
lengths.

Table of Contents

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Heathkit HW-9 and is the answer not in the manual?

Heathkit HW-9 Specifications

General IconGeneral
BrandHeathkit
ModelHW-9
CategoryTransceiver
LanguageEnglish

Related product manuals