Hercules 10 User Manual

10 Zone LED Alarm Panel - Engineering Manual
1
Hercules 10 Zone onboard LED Alarm Panel
Engineering Manual
SAFETY
Before proceeding with the installation, please note the following safety warnings:
DO NOT connect the mains supply directly to the product, this will cause permanent damage to the products.
Control panel is for indoor use only. Avoid mounting location which can expose this product to splashing or dripping
liquid.
Always follow the manufacturer’s advice when using any tools power tools, ladder/steps,. using steps or ladders, and
wear suitable protective equipment (e.g. safety goggles) when drilling holes, etc. The use of ear defenders are advisable
when working in close proximity to the External Siren or the Control Panel’s Siren when the front panel cover is
removed due to the high sound level produced by it. Before drilling holes in walls, check for hidden electricity cables
and water pipes. The use of a cable/pipe locator is advisable if in doubt. Batteries (battery pack or batteries installed)
should not be exposed to excessive heat. Danger of damage to the unit may occur if battery is incorrectly replaced.
Replace only with the same or equivalent type. (Do not mix batteries type).

Hercules 10 Specifications

General

Smart Home Compatibility	Amazon Alexa, Google Assistant
Model	Hercules 10
Connectivity Protocol	Wi-Fi
Features	Motion detection, Door/window sensors
Type	Wireless Security System
Power Supply	AC Adapter
Battery Backup	Yes
Sensors Included	Door/Window Sensors, Motion Detector
Mobile App	Yes (iOS and Android)
Cloud Storage	Optional subscription

Summary

SAFETY

SECTION 1 - OVERVIEW OF SYSTEM

1.1 - Kit Contents

Lists the components included in the alarm system kit.

1.2 - Tools Required

Lists the tools necessary for installing the alarm system.

1.3 - System Features

Details the key features and capabilities of the alarm system.

1.4 - Explanation of Terms

Defines common terms and abbreviations used in the manual.

SECTION 2 – INSTALLING YOUR SYSTEM

2.1 - Fixing the Control Panel

Instructions on how to mount and secure the main control panel.

2.2 - PCB Layout and Fuses

Details the Printed Circuit Board layout, components, and fuse information.

2.3 - Tamper Network Configuration

Explains the tamper circuit for detecting unauthorized access to cables and detectors.

2.4 - Remote Keypad Installation

Information on connecting and configuring remote keypads, including jumpers.

2.5 - Security Zones Wiring

Describes how to connect and configure security zones using PIR and MS detectors.

2.6 - Fire Zone Circuit

Details the wiring and function of fire zones.

2.7 - Tamper Zone Circuit

How to configure zones for tamper detection.

2.8 - PA Zone Circuit

Wiring and setup for Personal Attack (PA) zones.

2.9 - Extension Speaker Connection

Instructions for connecting an external speaker to the control panel.

2.10 - External Siren Output (Bell Box)

Wiring and configuration for the external siren and strobe.

SECTION 3 - FACTORY DEFAULT SETTING

SECTION 4 - MAINS CONNECTION

SECTION 5 - FIRST POWER UP

SECTION 6 – HOW TO SET UP THE SYSTEM

6.1 - Entering Engineer Program Mode

Guide on accessing the system's engineer programming mode.

6.2 - Setting Up Programs

Details on setting up system programs like Full, Part1, and Part2.

6.3 - Setting Zone Types

Instructions for assigning types (Security, Fire, PA) to zones.

6.4 - Setting Zone Attributes

Configuration of zone attributes like Omit Allowed, Double Knock, Chime.

6.5 - Setting Access Codes

Procedures for setting up user, manager, and engineer access codes.

6.6 - System Setup Options

System configuration options including flags, bell time, and rearm counts.

6.7 - Viewing Event Log

How to access and view the system's event log.

6.8 - Testing the System

Procedures for testing system outputs and performing walk tests.

SECTION 7 - USING THE SYSTEM

7.1 - Setting the System

Steps for arming the system in various modes (Full, Part1, Part2).

7.2 - Omitting Zones

Procedure for temporarily disabling a zone from the alarm system.

7.3 - Unsetting the System

Steps for disarming the system using user or manager codes.

7.4 - Unsetting from Alarm and Resetting

Procedures to unset the system and reset it after an alarm.

7.5 - Using the Panic Alarm

Instructions for activating the panic alarm function from the keypad.

SECTION 8 - MAINTENANCE

SECTION 9 - TROUBLESHOOTING GUIDE

SECTION 10 - SPECIFICATIONS

Appendix 1 – Zone Location Table

Disposal and Recycling

Technical Support