How to troubleshoot 'DEVICE FAIL' on HIKVISION Security System?
If your HIKVISION Security System displays 'DEVICE FAIL xxx xxx = OM xxx = ZEM xxx = Kpd xxx = Trd xxx = Pnl', identify the device. Check that the device is addressed correctly to match the programming. Check the connections at the device and the cabling to it. If the above are correct, reboot the device, followed by a reboot of the End Station.
How to troubleshoot 'CALL FAIL TO ARC' on HIKVISION Security System?
If your HIKVISION Security System displays 'CALL FAIL TO ARC', check that ALL call details are programmed correctly and ensure that the signaling format is correctly set for the ARC receiver.
What to do if HIKVISION Security System shows 'LINE FAULT'?
If your HIKVISION Security System displays 'LINE FAULT': a) Make sure the SIM card is plugged into the modem/communications module. b) Make sure the GPRS signal is good enough.
How to fix 'MODEM FAULT' on HIKVISION Pyronix EURO 46 V10 Security System?
If your HIKVISION Security System displays ‘MODEM FAULT’: * If the modem is not present, ensure the ‘Disable Digi’ option is set to ‘YES’ and ‘DOWNLOAD MODE’ is set to ‘NONE’ or ‘RS232’. * If the modem is present but not detected, check the Digi Modem cable is connected correctly.
How to fix 'Engineer Access Denied' on HIKVISION Security System?
If your HIKVISION Security System displays 'Engineer Access Denied', ensure that ALL areas are unset, using suitable user codes/tags at the appropriate keypads/readers.
How to resolve 'Error some Areas cannot be unset' on HIKVISION Pyronix EURO 46 V10?
If your HIKVISION Security System displays 'Error some Areas cannot be unset', you must adjust the programming before exiting Engineer mode.
How to fix a blank keypad display on HIKVISION Pyronix EURO 46 V10?
If your HIKVISION Security System keypad display is blank, check the keypad address by pressing and holding the [D] key until the security code is requested. Enter ‘2000’ and set the keypad address. Note that the primary keypad address is set to [00] by default.
How to resolve 'Check Failed Input xxx' on HIKVISION Pyronix EURO 46 V10?
If your HIKVISION Security System displays 'Check Failed Input xxx', check for the fault on the input, or omit it in programming. This applies to 24-hour tamper, other input types that would generate an alarm if the system were returned to unset mode, and tamper faults on other input types.
What does '485/COMMS LOST' mean on my HIKVISION Security System?
If your HIKVISION Security System displays '485/COMMS LOST', this is part of the routine initialisation procedure. If it persists, check the display at other keypads to see if the failure is at the keypad or a complete system BUS failure. Temporarily install an additional keypad to diagnose.
How to prevent 'Alarm during the setting procedure' on HIKVISION Pyronix EURO 46 V10?
If your HIKVISION Security System displays 'Alarm during the setting procedure', do not activate ‘instant inputs’ during the setting procedure.
General| Zones | 46 |
|---|---|
| Wired zones on board | 8 |
| Keypads | Up to 4 |
| Areas | 4 |
| Operating Temperature | -10°C to +40°C |
| Type | Control Panel |
| Outputs | 4 |
| Communication | PSTN |
| Radio frequency | 868MHz |
| Backup battery | 7Ah |
| Product Type | Security System |
Manages learning and deleting wireless inputs, bells, and arming stations.
Configures input types, areas, and attributes.
Details attributes like Chime, Omittable, Double Knock, etc., for inputs.
Configures input resistance, EOL mode, and response time.
Guides the process of enabling and configuring ZEMs on the EURO system.
Configures the programming of outputs on the EURO 46 V10.
Ensures keypads and readers are correctly addressed and configured.
Configures various site-specific behaviors and fault handling.
Defines how the system exits, e.g., Timed, Final Door, Push to Set.
Allows viewing and analyzing panel and access control logs.
Enables testing of all programmed inputs on the system.
Analyzes wireless device signal strength as a percentage.
Measures battery levels for wireless devices and provides status.
Explains how to set up uploading/downloading via InSite software.
Resets the panel settings to default, including deleting wireless data, codes, and logs.
Lists options for addressing, language, zone status, volume, and reset.
Details the steps for connecting the panel to InSite software via the cloud.
Guides on configuring the PC software for cloud connection.
Steps to configure the panel for RS232 connection.
Steps to configure the PC software for RS232 connection.
Identifies faults related to devices not installed or lost from the bus.
Details troubleshooting for communications faults (Modem, Line, ARC).
Addresses issues with wired devices on the RS485 bus.
Covers faults like Case Tamper and Code Guessing.
Addresses issues related to battery and mains power supply.
Details faults specific to wireless devices like low battery or jamming.
Explains common errors during the setting procedure and their solutions.
To Next Page