What to do if HIKVISION Pyronix EURO 46 V10 triggers 'Alarm during the setting'?
If your HIKVISION Security System displays 'Alarm during the setting', leave the premises within the fail to set time, increase the fail to set time in ‘timers’ or disable this feature in system options.
How to fix 'Authorisation Required' on HIKVISION Pyronix EURO 46 V10 Security System?
If your HIKVISION Security System displays 'Authorisation Required', the 'Allow Engineer Menu' option needs to be enabled by the master manager.
What does 'BAT CRITICAL' mean on my HIKVISION Pyronix EURO 46 V10?
If your HIKVISION Security System displays 'BAT CRITICAL', it protects the battery from deep discharge damage during an extended mains failure. Note that the system is about to power down!
What does 'BAT LOAD FAIL' mean on my HIKVISION Pyronix EURO 46 V10 Security System?
If your HIKVISION Security System displays 'BAT LOAD FAIL', and the option is selected, it means the battery is uncharged or its capacity is below specification, and it may need replacing.
How to resolve 'WLs JAMMING Pnl' on HIKVISION Pyronix EURO 46 V10 Security System?
If your HIKVISION Security System displays 'WLs JAMMING Pnl', check for any radio interference near the radio devices or the panel.
What to do if HIKVISION Security System displays 'Unable To Set'?
If your HIKVISION Security System displays 'Unable To Set', correct the problem if an input is open, or call an engineer.
How to fix 'CASE TAMPER' error on HIKVISION Pyronix EURO 46 V10?
If your HIKVISION Security System shows 'CASE TAMPER', make sure the tamper switch is closed.
What does 'LOW VOLTS' mean on HIKVISION Pyronix EURO 46 V10 Security System during mains failure?
If your HIKVISION Security System displays 'LOW VOLTS' during a mains failure, it means the battery voltage is below the normal 'battery fault' level.
How to clear 'Code Guessing' on HIKVISION Security System?
If your HIKVISION Security System displays 'Code Guessing', press the ‘NO’ key to clear the message.
What does 'BATTERY FAULT' mean on my HIKVISION Pyronix EURO 46 V10 Security System?
If your HIKVISION Security System shows 'BATTERY FAULT', this is normal during recharge after a mains failure.
General| Zones | 46 |
|---|---|
| Wired zones on board | 8 |
| Keypads | Up to 4 |
| Areas | 4 |
| Operating Temperature | -10°C to +40°C |
| Type | Control Panel |
| Outputs | 4 |
| Communication | PSTN |
| Radio frequency | 868MHz |
| Backup battery | 7Ah |
| Product Type | Security System |
Manages learning and deleting wireless inputs, bells, and arming stations.
Configures input types, areas, and attributes.
Details attributes like Chime, Omittable, Double Knock, etc., for inputs.
Configures input resistance, EOL mode, and response time.
Guides the process of enabling and configuring ZEMs on the EURO system.
Configures the programming of outputs on the EURO 46 V10.
Ensures keypads and readers are correctly addressed and configured.
Configures various site-specific behaviors and fault handling.
Defines how the system exits, e.g., Timed, Final Door, Push to Set.
Allows viewing and analyzing panel and access control logs.
Enables testing of all programmed inputs on the system.
Analyzes wireless device signal strength as a percentage.
Measures battery levels for wireless devices and provides status.
Explains how to set up uploading/downloading via InSite software.
Resets the panel settings to default, including deleting wireless data, codes, and logs.
Lists options for addressing, language, zone status, volume, and reset.
Details the steps for connecting the panel to InSite software via the cloud.
Guides on configuring the PC software for cloud connection.
Steps to configure the panel for RS232 connection.
Steps to configure the PC software for RS232 connection.
Identifies faults related to devices not installed or lost from the bus.
Details troubleshooting for communications faults (Modem, Line, ARC).
Addresses issues with wired devices on the RS485 bus.
Covers faults like Case Tamper and Code Guessing.
Addresses issues related to battery and mains power supply.
Details faults specific to wireless devices like low battery or jamming.
Explains common errors during the setting procedure and their solutions.
To Next Page