Hilti SCM 22-A - User Manual

Other manuals for Hilti SCM 22-A

Questions and Answers

J
Jonathan AguilarSep 12, 2025
Why is my Hilti Power Tool circular saw or battery getting so hot?
- T
  Tommy CarterSep 12, 2025
  If your Hilti Power Tool's circular saw or battery is getting very hot, immediately switch off the circular saw, remove the battery, and keep it under observation, allowing it to cool down. This could be due to an electrical fault or because the product is overloaded, exceeding its application limits. Pay attention to the power and performance rating of the product before using it, and check its suitability for the job.
A
Anita ThomasSep 12, 2025
How to fix Hilti SCM 22-A battery not engaging with double click?
- B
  Brandon HansenSep 12, 2025
  If the battery isn't engaging with a double click on your Hilti Saw, the retaining lugs on the battery may be dirty. Clean the retaining lugs and refit the battery.
E
evelyngilmoreSep 9, 2025
Why does the running speed drop on my Hilti SCM 22-A Saw?
- E
  Elizabeth SmithSep 10, 2025
  If the running speed of your Hilti Saw suddenly drops, it could be because the saw blade is jamming. Make sure not to tilt the saw blade.
D
denise73Sep 8, 2025
What causes the saw blade to stall on a Hilti SCM 22-A Saw?
- A
  agreenSep 8, 2025
  If the saw blade of your Hilti Saw stalls, it's likely because the saw advance pressure is too high. Reduce the advance pressure and switch the product back on.
T
Tracy GomezSep 7, 2025
What to do if chips fall onto the base plate of my Hilti SCM 22-A?
- R
  Ryan SimmonsSep 7, 2025
  If chips or cuttings from your Hilti Saw are falling onto the base plate instead of going into the chip collector, the chip collector might be full, so empty it. Alternatively, the chip ejector channel could be blocked, so try cleaning it.
J
Jenna MooreAug 23, 2025
What to do if my Hilti SCM 22-A Saw gets very hot?
- S
  savagestevenAug 23, 2025
  If the Hilti Saw or its battery gets very hot, immediately switch off the circular saw, remove the battery, and keep it under observation. Allow it to cool down. This could be due to an electrical fault or because the product is overloaded. Pay attention to the power and performance rating of the product before using it and check its suitability for the job.
E
Elizabeth ReyesSep 5, 2025
How to unlock the on/off button on a Hilti SCM 22-A?
- M
  Michael TrevinoSep 5, 2025
  If the on/off button on your Hilti Saw is locked, it's likely due to the safety function. Simply press the safety lock to release it.
G
griffingarySep 4, 2025
Why is my Hilti SCM 22-A or battery getting very hot?
- M
  Mr. Harry Woods DDSSep 4, 2025
  If your Hilti Saw or its battery is getting very hot, immediately switch off the circular saw, remove the battery, and keep it under observation, allowing it to cool down. This could be due to an electrical fault or the product being overloaded. Pay attention to the power and performance rating of the product before using it, i.e check its suitability for the job on hand. See 'Technical data' section.
R
Robert DukeSep 3, 2025
Why are 4 LEDs blinking on my Hilti SCM 22-A Saw?
- Z
  zberrySep 3, 2025
  If you notice 4 LEDs blinking on your Hilti Saw, it could mean one of two things: either the circular saw was briefly overloaded, in which case you should release the control switch and press it again, or the overheating prevention cut-out has been activated. If it's the latter, allow the circular saw to cool down and clean the air vents.
T
Theodore ThomasSep 2, 2025
What to do if the LEDs indicate nothing on my Hilti SCM 22-A Saw?
- A
  Aaron MorenoSep 2, 2025
  If the LEDs on your Hilti Saw don't light up, it could be due to a couple of reasons. First, make sure the battery is fully inserted until you hear a double click. If that's not the issue, the battery might be discharged. In that case, try swapping it with a charged battery.