HIMA HIMax X-COM 01 E - 3.5.8 Indicators

46 pages

To Next Page

To Previous Page

3 Product Description X‑COM 01 E

Page 16 of 46 HI 801 566 E Rev. 13.00.00

3.5.8 Indicators

The following figure shows the front view of the module with the LEDs.

Figure 4: Front View

Main Page

Table of Contents3
Introduction5
Structure and Use of this Manual5
Target Audience5
Table 1: Additional Applicable Manuals5
Presentational Conventions6
Warning Messages6
Useful Additional Information7
Safety8
Intended Use8
Environmental Conditions8
ESD Protective Measures8
Residual Risk8
Safety Precautions8
Emergency Information8
Product Description9
Replacement and Compatibility9
Downgrade9
Safety Function10
Response in the Event of a Fault10
Scope of Delivery10
Type Label11
Figure 1: Sample Type Label11
Structure12
Block Diagram with X-CB 001 02 Connector Board12
Figure 2: Block Diagram with X-CB 001 02 Connector Board12
Block Diagram with X-CB 001 04 Connector Board13
Figure 3: Block Diagram with X-CB 001 04 Connector Board13
Processor System14
Ethernet Switch14
Ethernet Interface14
Fieldbus Interfaces on the X-CB 001 02 Connector Board14
Table 2: Ethernet Interface Properties14
Table 3: Fieldbus Interface Specifications14
Automation Network and Fieldbus Interfaces on the X-CB 001 04 Connector Board15
Table 4: Data for the Automation Network Interface15
Table 5: Data for the Fieldbus Interface15
Indicators16
Figure 4: Front View16
Table 6: Blinking Frequencies of the Leds17
Module Status Indicators18
Redundancy Indicators18
Table 7: Module Status Indicators18
Table 8: Redundancy Indicators18
System Bus Indicators19
Fieldbus and Automation Network Indicators19
Table 9: System Bus Indicators19
Table 10: Fieldbus and Automation Network Indicators19
Ethernet Indicators20
Table 11: Ethernet Indicators20
Product Data21
Figure 5: Views21
Table 12: Product Data21
Connector Board22
Ports on the X-CB 001 02 Connector Board22
Figure 6: X-CB 001 02 Connector Board22
Table 13: Connection Sockets on the X-CB 001 02 Connector Board23
Ports on the X-CB 001 04 Connector Board24
Figure 7: X-CB 001 04 Connector Board24
Table 14: Connection Sockets on the X-CB 001 04 Connector Board25
Start-Up26
Mounting26
Mounting and Removing the Module26
Mounting a Connector Board26
Figure 8: Example of How to Insert the Mono Connector Board27
Figure 9: Example of How to Secure the Mono Connector Board with Captive Screws28
Mounting and Removing a Module29
Figure 10: Mounting and Removing a Module30
Configuring the Module in Silworx31
The Module Tab31
The Routings Tab33
Table 15: Configuration Parameters, Module Tab33
Table 16: Routing Parameters33
The Ethernet Switch Tab34
The VLAN Tab (Port-Based VLAN)34
Table 17: Ethernet Switch Parameters34
Table 18: VLAN Tab34
The LLDP Tab35
The Mirroring Tab35
Table 19: Values for LLDP35
Network Ports in Use for Ethernet Communication36
Table 20: Network Ports (UDP Ports) in Use36
Table 21: Network Ports (TCP Ports) in Use36
Operation37
Handling37
Diagnostics37
Maintenance38
Maintenance Measures38
Proof Test38
Loading of Enhanced Operating System Versions38
Decommissioning39
Transport40
Disposal41
Appendix42
Glossary42
Index of Figures43
Index of Tables43
Index44

HIMA HIMax X-COM 01 E - 3.5.8 Indicators

Table of Contents

Related product manuals