Hioki IM3536-01 - Page 268

Ind.4
Index
Signal assignments ................................................ 162
Signal level ............................................................... 49
Specications ......................................................... 187
Speed
...............................................................
55, 217
SPEED key
............................................................... 55
Spot correction (Open correction)
.......................... 103
Spot correction (Short correction)........................... 107
Standards ............................................................... 192
Storage temperature and humidity
......................... 192
Superimpose a DC voltage.......................................
60
Susceptance
............................................................. 40
Suspended state.......................................................
37
Symbols .....................................................................
11
SYS screen............................................................... 28
System...................................................................... 28
Test......................................................................
133
System reset...................................................
228, 229
System settings
................................................ 28, 131
T
Terminals .................................................................. 18
The instrument doesn’t work. ................................. 224
Timing ....................................................................... 66
Timing charts .................................................. 171–175
EXT I/O
............................................................... 171
Touch screen
............................................................ 20
TOUCH SCREEN TEST key .................................. 133
Transport ............................................................
1, 222
T
rigger ................................................................ 63–64
Trigger delay ................................................. 64, 66–67
Trigger input
Disabled
.............................................................. 182
Effective edge .....................................................
182
Trigger synchronous delay ........................... 65, 66–67
Trigger synchronous output
.......................... 65, 66–67
TRIG key
......................................................
63–64, 94
Turning power on ................................................ 13, 36
TYPE key........................................................
143, 151
U
Unable to communicate with RS-232C................... 227
Unable to perform measurement properly (Unusual
measurement value) ....................................... 225–226
UNLOCK key ............................................................
92
USB connector ................................................. 19, 205
USB ash drive ........................................... 14–15, 137
Checking the contents of a le
............................ 157
Checking the contents of les ............................. 139
Creating folders
................................................... 159
Deleting les and folders
..................................... 158
Format .................................................................
140
Information .......................................................... 160
Insert ................................................................... 138
Loading Instrument Settings ....................... 155–156
Saving measurement data
Percentage setting.............................................. 73, 78
Permittivity ..........................................................
40, 68
Phase angle..............................................................
40
Power cord
............................................................... 34
Power line
.......................................................... Appx.5
Power-saving
............................................................ 89
Power supply ...................................................... 18–19
Pre-operation inspection........................................... 33
Preparations
............................................................. 31
Probes
......................................................................
35
Q
Q&A ........................................................................ 223
External control
...................................................
185
Q factor ..................................................................... 40
R
Rack-mounting ................................................ Appx.12
Range
............................................................... 45, 190
RANGE key
............................................ 46, 47, 48, 56
Range synchronization function
............................... 80
rdg. ............................................................................ 11
Reactance
................................................................ 40
Repair ............................................................. 221, 223
Repair and Inspection.............................................
221
Replaceable parts...................................................
221
Replaceable Parts and Operating Lifetimes ........... 221
Residual charge protection ........................ 191, Appx.9
RNG SYNC key
........................................................
80
ROM/RAM test .......................................................
135
ROM/RAM TEST key ............................................. 135
RS-232C connector .......................................... 19, 206
S
SAVE key ................................................................ 153
SAVE TO... key ....................................................... 152
Saving settings data ....................................... 153–154
SCALE key ............................................................. 121
Scaling ............................................................ 121–122
Screen ...................................................................... 20
Screen copy.................................................... 150–151
Screen display status test.......................................
134
SELECT key ........................................................... 155
Self diagnosis ......................................................... 133
Series equivalent circuit................................... Appx.10
SET screen ............................................................... 25
Settings.....................................................................
24
External I/O settings ............................................ 180
Optional
................................................................. 43
Required................................................................
43
Shipping precautions
................................................ 13
Short correction ................................ 2–4, 105, Appx.11
Shorten the correction time .................................... 101
SHORT key ............................................. 106, 107, 111