Hitachi X200 Series - Page 272

List of Holding Registers
Network Data
Func.
Code
Name R/W Description
Reg. Range Res.
A092
(high)
R/W 1074h
A092
(low)
Acceleration (2) time
setting
R/W
Duration of 2nd segment of
acceleration, range is:
0.01 to 3000 sec.
1075h
1 to
300000
*1
0.01 sec
A292
(high)
R/W 1519h
A292
(low)
Acceleration (2) time
setting,
2nd motor
R/W
Duration of 2nd segment of
acceleration, 2nd motor, range is:
0.01 to 3000 sec.
151Ah
1 to
300000
*1
0.01 sec
A093
(high)
R/W 1076h
A093
(low)
Deceleration (2) time
setting
R/W
Duration of 2nd segment of
deceleration, range is:
0.01 to 3000 sec.
1077h
1 to
300000
*1
0.01 sec
A293
(high)
R/W 151Bh
A293
(low)
Deceleration (2) time
setting,
2nd motor
R/W
Duration of 2nd segment of
deceleration, 2nd motor, range is:
0.01 to 3000 sec.
151Ch
1 to
300000
*1
0.01 sec
A094 Select method to
switch to Acc2/Dec2
profile
R/W Two options for switching from
1st to 2nd accel/decel:
00 }2CH input from terminal
01 }Transition frequency
1078h
A294 Select method to
switch to Acc2/Dec2
profile, 2nd motor
R/W Two options for switching from
1st to 2nd accel/decel:
00}2CH input from terminal
01}Transition frequency
(2nd motor)
151Dh
0, 1

A095 Acc1 to Acc2 frequency
transition point
R/W Output frequency at which
Accel1 switches to Accel2, range
is 0.0 to 400.0 Hz
107Ah
A295 Acc1 to Acc2 frequency
transition point, 2nd
motor
R/W Output frequency at which
Accel1 switches to Accel2, 2nd
motor, range is 0.0 to 400.0 Hz
151Fh
0 to 4000 0.1 Hz
A096 Dec1 to Dec2 frequency
transition point
R/W Output frequency at which
Decel1 switches to Decel2, range
is 0.0 to 400.0 Hz
107Ch
A296 Dec1 to Dec2 frequency
transition point, 2nd
motor
R/W Output frequency at which
Decel1 switches to Decel2, 2nd
motor, range is 0.0 to 400.0 Hz
1521h
0 to 4000 0.1 Hz
A097 Acceleration curve
selection
R/W Set the characteristic curve of
Acc1 and Acc2, two options:
00}linear 01}S-curve
107Dh 0, 1

A098 Deceleration curve
selection
R/W Set the characteristic curve of
Dec1 and Dec2, two options:
00}linear 01}S-curve
107Eh 0, 1

A101 [OI]-[L] input active
range start frequency
R/W The output frequency
corresponding to the analog
input range starting point,
range is 0.0 to 400.0 Hz
1080h 0 to 4000 0.1 Hz
A102 [OI]-[L] input active
range end frequency
R/W The output frequency
corresponding to the current
input range ending point,
range is 0.0 to 400.0 Hz
1082h 0 to 4000 0.1 Hz
A103 [OI]-[L] input active
range start current
R/W The starting point (offset) for the
current input range,
range is 0. to 100.%
1083h 0 to 100 1 %
B29
Appendix B
B
−
29
Appendix B