Honeywell MagneW 3000 Plus - Ordering Data and Special Instructions

80 pages

To Next Page

To Next Page

To Previous Page

To Previous Page

Loading...

36 MagneW 3000

PLUS

Specification and Application Guide 1/98

Ordering Data and Special Instructions

Refer to the following model selection guides to build the appropriate model

numbers for the MagneW 3000

PLUS

components that you need to meet your

application requirements.

Table of Contents

Default Chapter3
- Table of Contents3
Introduction7
Figure 1 Magnew 3000 PLUS Components7
Components7
Principle of Operation8
Hardware Configuration8
- Figure 2 Principle of Operation8
Features9
Detector9
Converter9
Operator Interface10
- Figure 3 Typical SFC Connection to the 4 to 20 Ma Loop10
- Figure 4 Typical SFC Prompts10
- Figure 5 Digital Operator Panel Display (Configured for % Flow Range)10
Figure 6 Magnew 3000 PLUS Communications Hierarchy for TPS11
Diagnostics11
Communications Summary11
Summary of Magnew 3000 Plus Features12
- Figure 7 Overview of Magnew 3000 PLUS Wiring Requirements13
- Electrical Connection Considerations14
- Terminal Connections15
Wiring Summary13
- Figure 8 Typical Wiring Connections for the Magnew 3000 PLUS Remote and Integral Flowmeters15
- Cabling for Remote Detector/Converter16
- Figure 9 Cable Length Versus Fluid Conductivity16
Ranging Function17
- Figure 10 Direct Direction, Automatic Dual Range Transfer Hysteresis17
- Figure 11 Direct/Reverse Transfer Hysteresis17
Selection of Corrosion Resistant Materials18
Application Data Worksheet19
Installation Planning Considerations20
- Environmental Conditions20
- Fluid to be Measured21
- Measured Liquid Flow Conditions21
- Detector Location in Piping22
- Clearance for Maintenance24
Specifications25
- Performance25
- Design25
- Environmental and Operating Conditions29
- Table 7 Minimum and Maximum Ranges30
Dimensions2531
- Figure 12 Wall Mounting Dimensions31
- Figure 13 2-Inch Pipe Mounting Dimensions32
- Figure 14 Dimensions for Integral Model-Refer to Table 833
- Figure 15 Union Joint Dimensions - 2.5 MM to 15 MM (0.1 In. to 0.6 In.)34
- Figure 16 Hose Joint Dimensions - 2.5 MM to 15 MM (0.1 In. to 0.6 In.)35
- Figure 17 Idf/Tri-Clamp Dimensions - 2.5 MM to 15 MM (0.1 In. to 0.6 In.)36
- Figure 18 Wafer Dimensions - 2.5 MM to 15 MM (0.1 In. to 0.6 In.) and 25 MM to37
- Table 8 Dimensions for Figures 14 and 1838
- Figure 19 Flange Dimensions - 25 MM (1 In.)39
- Figure 20 Flange Dimensions - 40 MM to 140 MM (1.6 In. to 3.9 In.) and 150 MM to 600 MM (5.9 In. to 23.6 In.)-Refer to Table 940
- Table 9 Dimensions for Figure 2041
Ordering Data and Special Instructions42
Model Selection Guides43
- Magnew 3000 PLUS Integral Converter and MGG18D Wafer Style Detector43
- Magnew 3000 PLUS Integral Converter and MGG18F Flange Style Detector48
- Magnew 3000 PLUS Remote Converter53
- Magnew 3000 PLUS Remote Detector Wafer Type, Size 2.5-200Mm62
- Magnew 3000 PLUS Remote Detector Flange Type, Size 25-600Mm65
- Magnew 3000 PLUS Submersible Remote Detector Flange Type72
- Size 25-600Mm72
- Magnew 3000 PLUS Cables76

Related product manuals

Preview: Honeywell MiniRAE 3000+

Honeywell MiniRAE 3000+

Preview: Honeywell RMA 3000

Honeywell RMA 3000

Preview: Honeywell ENCAL 3000

Honeywell ENCAL 3000

Preview: Honeywell E-Mon

Honeywell E-Mon

Preview: Honeywell Vertex M

Honeywell Vertex M

Preview: Honeywell Minitrend

Honeywell Minitrend

Preview: Honeywell DVC100 (M) MK2

Honeywell DVC100 (M) MK2

Honeywell Class 320 Meter

Preview: Honeywell Envitec MySignO

Honeywell Envitec MySignO

Preview: Honeywell E-Mon Class 6200

Honeywell E-Mon Class 6200

Preview: Honeywell E-Mon Class 3200

Honeywell E-Mon Class 3200

Honeywell E-Mon EM3S-V-P-R