Honeywell MagneW 3000 Plus - Page 63

36-KI-16-31
Page 2 of 3
Availability
MGG18D
TABLE I (continued) Selection
D - Electrodes
SUS316L _ _ _ _ _ _ L _ _ _ _ _
*
Hastelloy C (with Teflon PFA only) _ _ _ _ _ _ C _ _ _ _ _ n
Titanium _ _ _ _ _ _ K _ _ _ _ _
Zirconium
(with Teflon PFA only) _ _ _ _ _ _ H _ _ _ _ _ n
Tantalum (with Teflon PFA only) _ _ _ _ _ _ T _ _ _ _ _ n
Tungsten Carbide (only for size 10mm and above) _ _ _ _ _ _ W _ _ _ _ _ e
Platinum-Iridium (with Teflon PFA only) _ _ _ _ _ _ P _ _ _ _ _ n
Alloy 20 (with Teflon PFA only) _ _ _ _ _ _ A _ _ _ _ _ c
Hastelloy B (with Teflon PFA only) _ _ _ _ _ _ B _ _ _ _ _ n
SUS304 (with Teflon PFA only) _ _ _ _ _ _ E _ _ _ _ _ c
Monel (with Teflon PFA only) _ _ _ _ _ _ M _ _ _ _ _ c
Nickel (with Teflon PFA 15-200mm only) _ _ _ _ _ _ N _ _ _ _ _ f
SUS316L Protruded Tip (with Teflon PFA 15-200mm only) _ _ _ _ _ _ 1 _ _ _ _ _ f
SUS316L for Alumina with Flat Tip (with Teflon PFA 15-200mm only) _ _ _ _ _ _ 2 _ _ _ _ _ f
SUS316L for Alumina with Pointed Tip (with Teflon PFA 15-200mm only)
_ _ _ _ _ _ 3 _ _ _ _ _
f
E - Grounding Rings
SUS316 _ _ _ _ _ _ _ S _ _ _ _
*
SS Top Hat Style (Upstream Only) _ _ _ _ _ _ _ G _ _ _ _ c
Hastelloy C (with Teflon PFA only) _ _ _ _ _ _ _ C _ _ _ _ c
Titanium _ _ _ _ _ _ _ K _ _ _ _
Zirconium
(with Teflon PFA only) _ _ _ _ _ _ _ H _ _ _ _ c
Tantalum (with Teflon PFA only) _ _ _ _ _ _ _ T _ _ _ _ c
Platinum (Note 3) _ _ _ _ _ _ _ P _ _ _ _ n
Alloy 20 (with Teflon PFA only) _ _ _ _ _ _ _ A _ _ _ _ c
Hastelloy B (with Teflon PFA only) _ _ _ _ _ _ _ B _ _ _ _ c
SUS304 (with Teflon PFA only) _ _ _ _ _ _ _ E _ _ _ _ c
SUS316L (with Teflon PFA only) _ _ _ _ _ _ _ L _ _ _ _ c
Nickel (with Teflon PFA only)
_ _ _ _ _ _ _ N _ _ _ _
c
F - Wiring Connection/Water Tight Gland
G1/2 Internal Thread without Water Tight Gland _ _ _ _ _ _ _ _ 2 _ _ _
(Not CSA/FM approved)
G1/2 Internal Thread with Brass (Ni-plated) Water Tight Gland _ _ _ _ _ _ _ _ 3 _ _ _
(Not CSA/FM approved)
G1/2 Internal Thread with Plastic Water Tight Gland _ _ _ _ _ _ _ _ 4 _ _ _
(Not CSA/FM approved)
1/2 NPT Internal Thread without Water Tight Gland _ _ _ _ _ _ _ _ 5 _ _ _
*
(CSA/FM NI approved)
CM20 Internal Thread without Water Tight Gland _ _ _ _ _ _ _ _ 6 _ _ _
(Not CSA/FM approved)
Pg13.5 Internal Thread without Water Tight Gland _ _ _ _ _ _ _ _ 7 _ _ _
(Not CSA/FM approved)
G1/2 Internal Thread with SUS304 Water Tight Gland _ _ _ _ _ _ _ _ 8 _ _ _
(Not CSA/FM approved)
G - Face to Face Dimension
Standard _ _ _ _ _ _ _ _ _ A _ _
*
Competitive (refer to Table 103 and consult factory)
_ _ _ _ _ _ _ _ _ 9 _ _
c
H - Installation/Wiring Direction
Upstream Side
(horizontal/vertical piping mounting) _ _ _ _ _ _ _ _ _ _ A _
*
Downstream Side (horizontal/vertical piping mounting) _ _ _ _ _ _ _ _ _ _ B _
Horizontal Piping Mounting/Left Side Viewed from Upstream _ _ _ _ _ _ _ _ _ _ C _
Horizontal Piping Mounting/Right Side Viewed from Upstream
_ _ _ _ _ _ _ _ _ _ D _