Honeywell SILENT KNIGHT 6700

To Next Page

To Previous Page

6700 Manual — P/N LS10148-001SK-E:F 8/29/2022 73

Notes

Main Page

Table of Contents5
Section 1: Introduction9
Basic System Overview9
1: Hardware Features9
2: Common Communication / Annunciation Link System Hardware Features9
3: Software Features9
About this Manual10
1: Terms Used in this Manual10
Compatible Products10
Related Documentation11
Section 2: Agency Listings, Approvals, and Requirements12
Federal Communications Commission (FCC)12
1: Electrical Safety Advisory12
Underwriters Laboratories (UL)13
1: Requirements for All Installations13
2: UL 864 9Th and 10Th Edition13
3: Requirements for Central Station Fire Alarm Systems13
4: Requirements for Local Protected Fire Alarm Systems13
5: Requirements for Remote Station Protected Fire Alarm Systems13
6: Requirements for the Installation of Carbon Monoxide (CO) Detection and Warning Equipment, NFPA 7214
7: NFPA Requirements14
Section 3: Prerequisites for Installation15
Inventory15
Environmental Specifications15
Software Downloads15
Electrical Specifications15
Calculating Current Draw and Standby Battery16
1: Worksheet Requirements16
2: Current Draw Worksheet for SK SLC Devices16
3: Current Draw Worksheet for SD SLC Devices20
Section 4: Control Panel Installation23
Mounting the Control Panel Cabinet23
1: Preventing Water Damage23
2: Removing the 6700 Assembly from the Housing23
3: Dead Front Installation and Removal23
Board Assembly Diagram25
Wiring Specifications25
AC Power Connection26
Battery Power27
1: Battery Accessory Cabinet27
Wiring Specifications29
1: Length Limitations29
2: Calculating Wiring Distance for SBUS Modules29
3: Wiring Configurations31
6855 Remote Annunciator Installation31
1: Mounting the 685532
2: 6855 Connection to the Panel34
5860 Remote Annunciator Installation34
1: Mounting the 586034
6860 Remote Annunciator Installation37
1: Mounting the 686037
2: 6860 Connection to the Panel39
5824 Serial/Parallel Printer Interface Module Installation39
1: Selecting 5824 Options39
5880 LED Driver Module40
1: 5880 Board Layout40
2: FACP Connection41
3: LED Wiring41
4: Dry Contact Wiring42
5865-3/5865-4 LED Annunciator Installation43
1: FACP Connection43
2: 5865 Mounting44
Configuring Modules44
1: Assigning Module Ids44
2: Communication Protocol45
3: End-Of-Line Resistor45
Telephone Connection46
Notification Appliance/Auxiliary Power Circuits46
1: Conventional Notification Appliance46
Class a Notification Wiring47
1: Auxiliary Power Installation47
Onboard Relays (Conventional)48
1: Common Trouble Relay48
2: Programmable Relays48
Remote Station Applications48
1: Keltron Model 3158 Installation48
2: City Box Connection Using the 5220 Module49
3: NFPA 72 Polarity Reversal50
4: Using a MR-201/T Control Relay from Air Products50
5: Transmitter Activated by Dry Contacts51
Section 5: Common Communication Link52
Hardware Features52
1: Panels52
Direct Connect Wiring Option52
NIC Wiring Options52
1: Fiber Loop Modules53
2: SK-NIC Mounting Kits53
NIC Installation53
1: Wiring54
Setting the ID for each Panel56
Section 6: Network Management57
Network Diagnostics57
1: Ping Panel57
2: Data Network Status57
Network Programming57
1: Learn Network57
2: Edit Network Names57
3: Edit Panel ID57
4: Computer Access58
5: Access Codes58
6: Communicator Options58
Sync Network Options59
Network Management Quick Reference60
Section 7: Programming Overview61
Jumpstart Auto-Programming61
1: Input Points61
2: Output Points61
3: Running Jumpstart Auto-Programming61
Mapping Overview62
1: Input Point Mapping63
2: Output Circuit Mapping63
3: Event Mapping63
4: Mapping LED Points65
Programming Using the HFSS Software Suite65
Programming Using an Annunciator65
1: Entering / Exiting the Program Menu65
2: Moving through the Menus66
3: Selecting Options and Entering Data66
Programming Menu Quick Reference66
Section 8: Programming74
UL 864 Programming Requirements74
Modules74
1: Edit Modules74
2: Adding Modules75
3: Deleting Modules75
4: View Module List75
Zone75
1: Edit Zone75
2: View Zone Points77
Group78
1: Edit Group78
2: View Group Points78
3: Edit Output Group Template78
Point79
1: Point Programming for SLC79
2: Point Programming for the Internal or External Power Module81
3: Point Programming for 5880 and 5865 Modules82
4: Point Programming for the 549683
System Options83
1: Communication Options83
2: Time Options86
3: Miscellaneous Options87
4: Daylight Saving Options87
5: Edit Banner88
6: SLC Family88
Jumpstart Auto-Programming88
Restore Defaults89
Section 9: System Operation90
Annunciator Description90
1: LCD Display90
2: Banner90
Menu System90
1: Panel Login Menu90
2: Main Menu Overview92
3: Using the Menus92
Basic Operation92
1: Setting Time and Date92
2: Disable / Enable a Point92
3: View Event History93
4: Conduct a Fire Drill93
5: Conduct an Indicator Test93
6: Conduct a Walk Test93
7: Conduct a Communicator Test94
8: Manual Alarmnet Registration94
9: Silence Alarms or Troubles94
10: Reset Alarms94
11: Check Detector Sensitivity through Point Status94
12: View Status of a Point95
13: View Alarms, Supervisories, or Troubles95
14: View System Information95
Operation Mode Behavior96
Panel Operating Modes96
1: Multi-Site Annunciator and Multi-Site User Access99
Releasing Operations99
1: Single Interlock Zone Releasing100
2: Double Interlock Zone Releasing100
Smoke Alarm Verification101
Function Keys101
1: Recording an F-Key Macro101
2: Aborting an F-Key Macro Recording Session101
3: Erasing an F-Key Macro101
4: Using a Recorded F-Key Macro102
5: F-Key Status Event102
6: F-Key Map Inhibit102
Section 10: Reporting103
Receivers Compatible with the Control Panel103
SIA / 6700 Panels PI Modifier Reporting112
SIA- 6700 Panel Communicator113
Section 11: Testing and Troubleshooting114
Troubleshooting114
Troubleshooting Common Problems114
1: Periodic Testing and Maintenance114
2: Event History115
Built-In Troubleshooting and Testing Tools115
1: SLC Device Locater115
2: SLC Multi Locater115
3: I/O Point Control116
Earth Fault Resistance116
Section 12: Installation Records117
SD SLC Device Point Record117
SLC Device Point Record118
Appendix A: Editing Text Using the Built-In Programmer119
A.1: Characters Used for Editing Text119
A.2: Edit Name Example119
Appendix B: Expanded Receiver/Panel Relationship120
Appendix C: Cadence Patterns121
Appendix D: Panel Security122
Model 6700 Basic Operating Instructions123

Honeywell SILENT KNIGHT 6700 - Page 73

Table of Contents

Related product manuals