Honeywell VISTA-128FBPT - Figure 3-25: Connecting the Backup Batteries

104 pages

To Next Page

To Previous Page

Figure 3-25: Connecting the Backup Batteries

Main Page

Table of Contents3
List of Figures5
Conventions Used in this Manual6
Ul864 (Commercial Fire) Compliance7
General Requirements7
Programming Field Settings for UL864 Compliance7
Programming Field Settings for ULC304 Compliance10
Section 1: General Description11
SIA Installations11
About the VISTA-128FBPT/VISTA-250FBPT11
Features11
Guidelines for Wiring a System15
Figure 1-1: Isolating Fire Devices from Burglary Devices16
Section 2: Partitioning17
Theory of Partitioning17
Setting-Up a Partitioned System17
Common Lobby Logic17
Master Keypad Setup and Operation19
Section 3: Installing the Control21
Mounting the Control Cabinet21
Installing the Cabinet Lock21
Figure 3-1: Installing the Lock21
Mercantile Premises Listing Guidelines22
Mercantile Safe and Vault Listing Guidelines22
Figure 3-2: Cabinet Attack Resistance Considerations22
Commercial Fire Guidelines23
Installing the Control's Circuit Board23
Figure 3-3: Commercial Fire Installation Considerations23
Installing the Keypads24
Figure 3-4: Mounting the PC Board24
Figure 3-5: Keypad Connections to Control Panel25
Figure 3-6. ECP Isolator Wiring25
Installing External Sounders26
Figure 3-7. Using a Supplementary Power Supply26
Auxiliary Relay Connections29
Telephone Line Connections30
Figure 3-8: Wiring Auxiliary Relay for Alarm Activation30
Figure 3-9: Wiring Auxiliary Relay for Smoke Detector Reset30
Main Dialer Connections31
Wiring Burglary and Panic Devices to Zones 1-832
Figure 3-10: 2-Wire Smoke Detector on Zone 1 (for Zone 2 Use Terminals 17 and 18)33
Figure 3-11: 4-Wire Smoke Detectors34
Installing V-Plex Devices35
Figure 3-12: Wiring a Normally Closed Sensor Loop for Tamper Supervision35
Figure 3-13: Wiring a Normally Open Sensor Loop for Tamper Supervision35
Figure 3-14: Polling Loop Connections to the Control Panel36
Figure 3-15: Polling Loop Connections Using One 4297 Extender Module37
Figure 3-16: Polling Loop Connections Using Multiple Extender Modules37
Wireless Zone Expansion38
Figure 3-17: Installing the 5881ENHC with Tamper Protection39
Figure 3-18: 5881ENHC RF Receiver (Cover Removed)39
Installing Output Devices41
Figure 3-19: 4204 Relay Module42
Figure 3-20: 4204CF Relay Module42
Installing a Remote Keyswitch43
Installing a Remote Keypad Sounder (for Commercial Burglary Use Only)44
Figure 3-21: Remote Keyswitch Wiring44
Figure 3-22: Remote Keypad Sounder Wiring44
Communicators Connected to the ECP Bus45
Access Control Using Vistakey46
Figure 3-23: Wiring Communicator to Keypad Terminals46
Event Log Connections48
RS-232 Connectivity48
Figure 3-24: Wiring the Vistakey48
Connecting the Transformer50
Earth Ground Connections50
Determining the Control's Power Supply Load50
Determining the Size of the Standby Battery55
Figure 3-25: Connecting the Backup Batteries56
Section 4: Downloading57
General Information57
Unattended Download (for Burglary Use Only)58
Getting On-Line with a Control Panel58
Direct-Wire Downloading59
Telco Handoff59
Section 5: Setting the Real-Time Clock61
General Information61
Setting the Time and Date61
Section 6: User Access Codes63
General Information63
User Codes and Levels of Authority63
Multiple Partition Access64
Adding a Master, Manager, or Operator Code65
Changing a Master, Manager, or Operator Code66
Deleting a Master, Manager, or Operator Code66
Exiting the User Edit Mode67
Section 7: Testing the System69
Battery Test69
Dialer Test69
Fire Drill Test (Code + [#] + 69)69
One-Man Fire Walk-Test (Code + [#] + 68)69
Burglary70
Walk-Test70
Walk Testing the 'Smart' V-Plex Motion Detectors71
Armed Burglary System Test71
Testing Wireless Transmitters71
Trouble Conditions72
To the Installer73
Regulatory Agency Statements75
UL Installation Requirements75
UL864/NFPA Local Fire75
UL864/NFPA Central Station and Remote Station Fire75
Commercial Burglary Requirements75
UL609 Local Mercantile Premises/Local Mercantile Safe & Vault75
UL365 Police Station Connected Burglar Alarm76
UL365/UL609 Bank Safe and Vault Alarm System76
UL1610 Central Station Burglary Alarm76
ULC Installation Requirements76
Summary of System Commands81
Appendix B: Specifications83
Contact ID Codes85
Table of Contact ID Event Codes85
Event Log Alpha Descriptors86
Glossary89
Index95

Honeywell VISTA-128FBPT - Figure 3-25: Connecting the Backup Batteries

Table of Contents

Other manuals for Honeywell VISTA-128FBPT

Related product manuals