The chart below shows all the adjustable parameters.
Follow the procedure outlined in step 1 to make any necessary changes.
ADJUSTABLE PRESET PARAMETERS
***Defaults: 2001 = 3 2003 = 1
**This parameter changes the braking force during opening.
3 is the most forceful with 0 being the mildest
*Time delay is 2-8, 10, 12,14, 16, 20, 25, 30 or 60 seconds.
BELT DRIVE
CODE
-The display will show the current value or setting of
the parameter.
-When the SET button is released, the display will show
the parameter that was just changed. Another parameter
may be changed, or the toggle circuit turned on to check the
changes just made. In versions 2.12 and up the SET button
may be double clicked to exit the menu (toggle must be on).
-With the display reading 2d press and HOLD the
SET button until dS (data save) is displayed. All of the
changes are now stored in the control's memory.
This step must be performed or the control will revert to
the default settings after a power failure.
-Set the reversing sensitivity as required using R10. Do not
leave this adjustment at minimum. Horton recommends setting
the sensitivity so the door will reverse at 28 ft.lb. or less.
-When all adjustments have been made and checked, be
sure the toggle circuit is on.
2nd Step -Saving new settings
-While holding the SET button,
press the UP or DOWN button to modify the setting.
2.04761
09-07
UP
DOWN
SET
R
+100
UP
+100
R
+100
SET
DOWN
R
A chart of preset values is shown to the right.
If any speeds or other settings need to be changed, follow this procedure:
14. ADJUSTING PARAMETERS
-The right decimal point will be blinking
-Refer to the chart in section 4 for a list of codes for
adjustable parameters.
-Scroll through the parameter list using the UP and
DOWN buttons until the parameter to be changed is
found.
-When the parameter to be changed is found, press
and hold the SET button.
-The display will switch to the menu of adjustable parameters
1st Step - Changing parameter settings
-Turn the toggle switch OFF
Or leave the toggle ON and
double click the SET button.
UP
UP
+100
SET
R
DOWN
DOWN
SET
+100
R
UP
SET
DOWN
H210.9
8
90% of total stroke
3
3***
3 (factory set - most senistive - 0 = off)
oF
on
on
on
oF
on
oF
oF
oF
oF
oF
oF
on
Left Hand parameter read only
total Stroke (read only)
Partial Open
stroke in inches
Check Point in inches
TYpe (read only)
Opening OBstruction detection
brake time**
1 Reserved parameter
no Adjustment permitted
brake on recycles
fail-SAfe lock
Lock present
reverse if no encoder Pulse
Jam Sensing
No stop during Find Close mode
Restricts close speed to 1ft/sec
4 Reserved parameters
Sidelite Protection
Lock in 1-way
daytime Lock
Unmonitored Lock
oF/on
0-4
0-3
0-3
oF/on
oF/on
oF/on
oF/on
oF/on
oF/on
oF/on
oF/on
oF/on
oF/on
oF/on
oF/on
oF
oF
on
OP
oF
oF
oF
3
3
4
9
10
2 sec
FACTORY PRESET VALUE
2 sec
3
3
1
3
Close braking
SLow speed bank
Power fail Night mode
Power Fail (open mode)
Reduce Accel
Auto Seal
cycle test
factory set - do not change
factory set - do not change
factory set - do not change
partial open delay
full open delay
Open cUshion
Close cUshion
Close Speed
CloseCheck
Open Check
Open Speed
PARAMETER
oF/on
oF/on
oF/on
OP/CL
oF/on
oF/on
oF/on
60*
60*
0-15
0-15
0-15
ADJUSTS
0-15
0-15
0-15
To Next Page
Loading...
Need help?
General
