*Time delay is 2-8, 10, 12, 14, 16, 18, 20, 25, 30, & 60 seconds
The chart below shows all the adjustable parameters for
version 1 software.
Follow the procedure outlined in step 9 to make any necessary changes.
4.ADJUSTABLE PRESET PARAMETERS
CODE
-The display will show the current value or setting of
the parameter.
-When the
SET
button is released, the display will show
the parameter that was just changed. Another parameter
may be changed, or the toggle circuit turned on to check the
changes just made. The
SET
button may be double clicked
to exit the menu (toggle must be on).
-With the display reading 2d press and
HOLD
the
SET
button until dS (data save) is displayed. All of the
changes are now stored in the control's memory.
This step must be performed
or the control will revert to
the default settings after a power failure.
-While holding the
SET
button,
press the
UP
or
DOWN
button to modify the setting.
-When all adjustments have been made and checked, be
sure the toggle circuit is on.
-Set the reversing sensitivity as required using R10.
Do not
leave this adjustment at minimum. Horton recommends setting
the sensitivity so the door will
reverse at 28 ft.lb.
or less.
2.0470d
05/08
10th Step -Saving new settings
DOWN
SET
UP
R
+100
UP
R
+100
+100
DOWN
SET
-Turn the toggle switch
OFF
Or, leave the toggle
ON
and double click the
SET
button
when the door is fully open or closed.
3. ADJUSTING PARAMETERS
9th Step - Changing parameter settings
A chart of preset values is shown to the right.
If any speeds or other settings need to be changed, follow this procedure:
-The display will switch to the menu of adjustable parameters
-Refer to the chart in section 4 for a list of codes for
adjustable parameters.
-Scroll through the parameter list using the
UP
and
DOWN
buttons until the parameter to be changed is
found.
-The right decimal point will be blinking
-When the parameter to be changed is found, press
and hold the
SET
button.
UP
UP
R
R
+100
+100
SET
DOWN
SET
DOWN
+100
2000 LINEAR DRIVE
UP
R
DOWN
SET
H210.3
oF
Slow speed bank
oF/on
3
20
oF
oF
oF
oF
oF
oF
oF
oF
on
oF
n
o
A
djustment permitted
4 reserved parameters
ty
pe (read only)
1 reserved parameter
b
rake
t
ime
2 reserved parameters
2 reserved parameters
L
onger
T
imeouts
5 reserved parameters
L
ock present
b
rake on
r
ecycles
d
aytime
L
ock
U
nmonitored
L
ock
C
lose
b
raking
L
ock in
1
-way
S
idelite
P
rotection
fail-
SA
fe lock
oF/on
0-4
0-100
oF/on
oF/on
oF/on
oF/on
oF/on
oF/on
oF/on
oF/on
oF/on
on
OP (power fail OPen)
oF
FACTORY PRESET VALUE
2 sec
2 sec
4
3
3
9
10
2
oF
oF
O
pen c
U
shion
P
ower fail
N
ight mode
P
ower
F
ail
R
educed
A
ccel
full open
d
elay
partial open time
d
elay
Factory set - do not change)
Factory set - do not change)
Factory set - do not change)
c
ycle
t
est
A
uto
S
eal
C
lose c
U
shion
3
3
1
PARAMETER
C
lose
C
heck
C
lose
S
peed
O
pen
S
peed
O
pen
C
heck
0-15
oF/on
Factory Set
Factory Set
Factory Set
OP/CL
oF/on
oF/on
oF/on
0-15
60*
60*
0-15
ADJUSTS
0-15
0-15
0-15
To Next Page
Loading...
Need help?
General
