HP 53131A/132A 225 MHz - Page 325

Index
Programming Guide Index-5
separator
keyword, 3-9
parameter, 3-12
serial control, 4-114
serial port, 4-43
service request enable register, 3-23, 4-139
short form, 3-53
single-quoted string
sending a single-quoted string, 3-58
slope, 4-84
standard deviation, 4-19
standard event status enable register, 3-26,
4-127
standard event status register, 3-24, 4-128
statistics, 4-19
enable, 4-21
filter, 4-23
maximum, 4-22
mean, 4-22
minimum, 4-22
N, 4-20
results, 4-19
standard deviation, 4-22
stats, 4-19
status
operation, 4-107
preset, 4-110
status byte register, 3-21, 4-140
status reporting, 3-38
flowchart, 3-41
summary of all registers, 3-19
stop, 3-10
string, 3-11, 3-18
HP BASIC, 3-58
parameters, 3-58
subsystem command
syntax, 3-8
Subsystem Commands, 4-4
:ABORt, 4-4
:CALCulate, 4-5
:CALCulate[1], 4-7
:CALCulate[1]:DATA?, 4-7
:CALCulate[1]:FEED, 4-8
:CALCulate[1]:IMMediate, 4-8
:CALCulate[1]:IMMediate
:AUTO, 4-9
:CALCulate[1]:MATH, 4-9
:CALCulate2
:CALCulate2:FEED, 4-11
:CALCulate2:IMMediate, 4-11
:CALCulate2:IMMediate
:AUTO, 4-12
:CALCulate2:LIMit, 4-12
:CALCulate3, 4-19
:CALCulate3:AVERage, 4-19
:CALCulate3:DATA?, 4-22
:CALCulate3:FEED, 4-23
:CALCulate3:LFILter, 4-23
:CALCulate3:PATH?, 4-25
:CALibration, 4-26
:CALibration:COUNt?, 4-26
:CALibration:DATA, 4-27
:CALibration:SECurity, 4-28
:CALibration[\:ALL]?, 4-26
:CONFigure, 4-30
:DIAGnostic, 4-32
:DIAGnostic:CALibration
:INPut[1|2]:GAIN:AUTO,
4-32
:DIAGnostic:CALibration
:INPut[1|2]:OFFSet:AUTO, 4-33
:DIAGnostic:CALibration
:INTerpolator:AUTO, 4-33
:DIAGnostic:CALibration
:ROSCillator:AUTO, 4-34
:DIAGnostic:CALibration
:STATus?, 4-34
:DIAGnostic:CALibration
:TINTerval:FINE, 4-35
:DIAGnostic:CALibration
:TINTerval:QUICk, 4-36
:DISPlay, 4-37
:DISPlay:[WINDow]:TEXT
:FEED, 4-38
:DISPlay:ENABle, 4-37
:DISPlay:MENU[:STATe], 4-37
:DISPlay[:WINDow]:TEXT
:RADix, 4-39
:FETCh, 4-40
:FORMat, 4-41
:FORMat[:DATA], 4-41
:HCOPy, 4-43
:INITiate, 4-44
:INITiate:AUTO, 4-44
:INITiate:CONTinuous, 4-44
:INITiate[:IMMediate], 4-46
:INPut[1|2], 4-48
:INPut[1|2]:ATTenuation, 4-48
:INPut[1|2]:COUPling, 4-48
:INPut[1|2]:FILTer[:LPASs]
:FREQuency?, 4-49
:INPut[1|2]:FILTer[:LPASs]
[:STATe], 4-48
:INPut[1|2]:IMPedance, 4-49
:INPut3, 4-50
:INPut3:COUPling?, 4-50