HP A6616 - Page 27

Item
MIM
Dimensions (H × W × D)
Hardware encryption
Power consumption
hot-swapping

For a Combo interface, the default operating interface is the

For a Combo interface, you can use either the electrical Ethernet interface or the optical
Ethernet interface. You can use the
view to switch between the optical and elec
enable { copper | fiber
} command, refer to
SR6600 Routers
User Manual

Use optical transceivers provided by
optical transceivers and thus displays alarms automatically.
 "Hot-
swapping" a module refers to first using the
the module, and then manually pulling it out, or inserting the module into its slot without
powering off the device. For details about the
Management in the
System Volume
LEDs
Figure 1-18 FIP-110 LEDs
(1) LED for 10/100/1000 Mbps electrical Ethernet interface 0 (GE0)
(2) LED for 10/100/1000 Mbps electrical Ethernet interface 1 (GE1)
(3) Run LED (RUN)
(4) 1000 Mbps optical Ethernet interface LED (SFP1)
(5) 1000
Mbps optical Ethernet interface LED (SFP0)
Table 1-21
Description of FIP
LED
RUN (green)
Off
Slow blinking (1 Hz)
Fast blinking (8 Hz)
Specification
4 MIMs supported at the same time
Dimensions (H × W × D)
45 × 399 × 412 mm (1.77 × 15.71 × 16.22 in.)
Supported
75 W
Supported
For a Combo interface, the default operating interface is the
electrical interface.
For a Combo interface, you can use either the electrical Ethernet interface or the optical
Ethernet interface. You can use the
combo enable { copper | fiber
} command in interface
view to switch between the optical and elec
trical interfaces. For details about the
} command, refer to
Ethernet Interfaces in the
Access Volume
User Manual
.
Use optical transceivers provided by
HP
only. The device may be incompatible with other
optical transceivers and thus displays alarms automatically.
swapping" a module refers to first using the
remove slot slot-number
the module, and then manually pulling it out, or inserting the module into its slot without
powering off the device. For details about the
remove slot
command, refer to
System Volume
of HP SR6600 Routers User Manual.
(1) LED for 10/100/1000 Mbps electrical Ethernet interface 0 (GE0)
(2) LED for 10/100/1000 Mbps electrical Ethernet interface 1 (GE1)
(4) 1000 Mbps optical Ethernet interface LED (SFP1)
Mbps optical Ethernet interface LED (SFP0)
Description of FIP
-110 LEDs
Status
Meaning
Off
No power input is available or the FIP
Slow blinking (1 Hz)
The FIP-
110 is working normally.
Fast blinking (8 Hz)
Application program is being loaded (in this case, never power
off the device or hot-
swap the FIP
may be damaged) or the FIP-
110 is not working.
Specification
45 × 399 × 412 mm (1.77 × 15.71 × 16.22 in.)
electrical interface.
For a Combo interface, you can use either the electrical Ethernet interface or the optical
} command in interface
trical interfaces. For details about the
combo
Access Volume
of HP
only. The device may be incompatible with other
command to stop
the module, and then manually pulling it out, or inserting the module into its slot without
command, refer to
Device
Meaning
No power input is available or the FIP
-110 has failed.
110 is working normally.
Application program is being loaded (in this case, never power
swap the FIP
-110; otherwise, the FIP-110
110 is not working.