To Next Page

To Previous Page

132

[SwitchA-vlan1001] description ToLAN

[SwitchA-vlan1001] quit

[SwitchA] vlan 4001

[SwitchA-vlan4001] description ToSAN

[SwitchA-vlan4001] quit

# Enable STP globally.

[SwitchA] stp global enable

# Configure interface Ten-GigabitEthernet 1/0/1 as a hybrid port.

[SwitchA] interface ten-gigabitethernet 1/0/1

[SwitchA-Ten-GigabitEthernet1/0/1] port link-type hybrid

# Assign Ten-GigabitEthernet 1/0/1 to VLAN 1001 as an untagged member.

[SwitchA-Ten-GigabitEthernet1/0/1] port hybrid vlan 1001 untagged

# Assign Ten-GigabitEthernet 1/0/1 to VLAN 4001 as a tagged member.

SwitchA-Ten-GigabitEthernet1/0/1] port hybrid vlan 4001 tagged

# Set the PVID to VLAN 1001 for the interface.

[SwitchA-Ten-GigabitEthernet1/0/1] port hybrid pvid vlan 1001

# Enable STP on Ten-GigabitEthernet 1/0/1.

[SwitchA-Ten-GigabitEthernet1/0/1] stp enable

[SwitchA-Ten-GigabitEthernet1/0/1] quit

# Configure interface Ten-GigabitEthernet 1/0/10 as a trunk port, and assign the interface to

VLAN 1001.

[SwitchA] interface ten-gigabitethernet 1/0/10

[SwitchA-Ten-GigabitEthernet1/0/10] port link-type trunk

[SwitchA-Ten-GigabitEthernet1/0/10] port trunk permit vlan 1001

# Enable STP on Ten-GigabitEthernet 1/0/10.

[SwitchA-Ten-GigabitEthernet1/0/10] stp enable

[SwitchA-Ten-GigabitEthernet1/0/10] quit

# Create Layer 2 aggregate interface 1, and configure it to operate in dynamic aggregation

mode.

[SwitchA] interface bridge-aggregation 1

[SwitchA-Bridge-Aggregation1] link-aggregation mode dynamic

# Disable STP on Layer 2 aggregate interface 1.

[SwitchA-Bridge-Aggregation1] undo stp enable

[SwitchA-Bridge-Aggregation1] quit

# Assign ports Ten-GigabitEthernet 1/0/5 through Ten-GigabitEthernet 1/0/8 to Layer 2

aggregation group 1.

[SwitchA] interface ten-gigabitethernet 1/0/5

[SwitchA-Ten-GigabitEthernet1/0/5] port link-aggregation group 1

[SwitchA-Ten-GigabitEthernet1/0/5] quit

[SwitchA] interface ten-gigabitethernet 1/0/6

[SwitchA-Ten-GigabitEthernet1/0/6] port link-aggregation group 1

[SwitchA-Ten-GigabitEthernet1/0/6] quit

[SwitchA] interface ten-gigabitethernet 1/0/7

[SwitchA-Ten-GigabitEthernet1/0/7] port link-aggregation group 1

[SwitchA-Ten-GigabitEthernet1/0/7] quit

[SwitchA] interface ten-gigabitethernet 1/0/8

Other manuals for HP FlexFabric 5700 series

Security Configuration Guide460 pages

Questions and Answers:

Need help?

Do you have a question about the HP FlexFabric 5700 series and is the answer not in the manual?

HP FlexFabric 5700 series Specifications

General

Layer Support	L2/L3
Routing Protocol	OSPF, BGP, RIP, IS-IS, Static Routing
Remote Management Protocol	SNMP, CLI, Web
Features	VXLAN
Compliant Standards	IEEE 802.1D, 802.1Q, 802.1w, 802.1s, 802.3ad
Operating Temperature	0°C to 45°C
Operating Humidity	10% to 90% (non-condensing)
VLANs	4K