To Next Page

To Previous Page

137

# Assign the interface to VLAN 4001 as a tagged member.

[SwitchC-Ten-GigabitEthernet1/0/1] port hybrid vlan 4001 tagged

[SwitchC-Ten-GigabitEthernet1/0/1] quit

# Create Layer 2 aggregate interface 1, and configure it to operate in dynamic aggregation

mode.

[SwitchC] interface bridge-aggregation 1

[SwitchC-Bridge-Aggregation1] link-aggregation mode dynamic

[SwitchC-Bridge-Aggregation1] quit

# Assign ports Ten-GigabitEthernet 1/0/5 through Ten-GigabitEthernet 1/0/8 to Layer 2

aggregation group 1.

[SwitchC] interface ten-gigabitethernet 1/0/5

[SwitchC-Ten-GigabitEthernet1/0/5] port link-aggregation group 1

[SwitchC-Ten-GigabitEthernet1/0/5] quit

[SwitchC] interface ten-gigabitethernet 1/0/6

[SwitchC-Ten-GigabitEthernet1/0/6] port link-aggregation group 1

[SwitchC-Ten-GigabitEthernet1/0/6] quit

[SwitchC] interface ten-gigabitethernet 1/0/7

[SwitchC-Ten-GigabitEthernet1/0/7] port link-aggregation group 1

[SwitchC-Ten-GigabitEthernet1/0/7] quit

[SwitchC] interface ten-gigabitethernet 1/0/8

[SwitchC-Ten-GigabitEthernet1/0/8] port link-aggregation group 1

[SwitchC-Ten-GigabitEthernet1/0/8] quit

# Configure Layer 2 aggregate interface 1 as a trunk port, and assign the aggregate interface to

VLAN 4001.

[SwitchC] interface bridge-aggregation 1

[SwitchC-Bridge-Aggregation1] port link-type trunk

[SwitchC-Bridge-Aggregation1] port trunk permit vlan 4001

[SwitchC-Bridge-Aggregation1] quit

3. Configure DCBX:

# Enable LLDP globally.

[SwitchC] lldp global enable

# Create Ethernet frame header ACL 4000.

[SwitchC] acl number 4000 name DCBX

# Configure the ACL to permit FCoE frames (protocol number is 0x8906) to pass through.

[SwitchC-acl-ethernetframe-4000] rule 0 permit type 8906 ffff

# Configure the ACL to permit FIP protocol packets (protocol number is 0x8914) to pass through.

[SwitchC-acl-ethernetframe-4000] rule 5 permit type 8914 ffff

[SwitchC-acl-ethernetframe-4000] quit

# Create a class named DCBX, with the operator of the class as OR.

[SwitchC] traffic classifier DCBX operator or

# Use ACL 4000 as the match criterion of the class.

[SwitchC-classifier-DCBX] if-match acl 4000

[SwitchC-classifier-DCBX] quit

# Create a behavior named DCBX.

[SwitchC] traffic behavior DCBX

# Configure the behavior to mark packets with 802.1p priority value 3.

Brand	HP
Model	FlexFabric 5700 series
Category	Switch
Language	English

HP FlexFabric 5700 series Configuration Guide

Table of Contents

Other manuals for HP FlexFabric 5700 series

Questions and Answers:

HP FlexFabric 5700 series Specifications

Related product manuals