To Next Page

To Previous Page

153

[SwitchC-vlan4001] description ToSAN_A

[SwitchC-vlan4001] quit

# Configure interface Ten-GigabitEthernet 1/0/1 as a hybrid port.

[SwitchC] interface ten-gigabitethernet 1/0/1

[SwitchC-Ten-GigabitEthernet1/0/1] port link-type hybrid

# Assign Ten-GigabitEthernet 1/0/1 to VLAN 4001 as a tagged member.

[SwitchC-Ten-GigabitEthernet1/0/1] port hybrid vlan 4001 tagged

[SwitchC-Ten-GigabitEthernet1/0/1] quit

# Create Layer 2 aggregate interface 1, and configure it to operate in dynamic aggregation

mode.

[SwitchC] interface bridge-aggregation 1

[SwitchC-Bridge-Aggregation1] link-aggregation mode dynamic

[SwitchC-Bridge-Aggregation1] quit

# Assign ports Ten-GigabitEthernet 1/0/5 through Ten-GigabitEthernet 1/0/8 to Layer 2

aggregation group 1.

[SwitchC] interface ten-gigabitethernet 1/0/5

[SwitchC-Ten-GigabitEthernet1/0/5] port link-aggregation group 1

[SwitchC-Ten-GigabitEthernet1/0/5] quit

[SwitchC] interface ten-gigabitethernet 1/0/6

[SwitchC-Ten-GigabitEthernet1/0/6] port link-aggregation group 1

[SwitchC-Ten-GigabitEthernet1/0/6] quit

[SwitchC] interface ten-gigabitethernet 1/0/7

[SwitchC-Ten-GigabitEthernet1/0/7] port link-aggregation group 1

[SwitchC-Ten-GigabitEthernet1/0/7] quit

[SwitchC] interface ten-gigabitethernet 1/0/8

[SwitchC-Ten-GigabitEthernet1/0/8] port link-aggregation group 1

[SwitchC-Ten-GigabitEthernet1/0/8] quit

# Configure Layer 2 aggregate interface 1 as a trunk port, and assign the aggregate interface to

VLAN 4001.

[SwitchC] interface bridge-aggregation 1

[SwitchC-Bridge-Aggregation1] port link-type trunk

[SwitchC-Bridge-Aggregation1] port trunk permit vlan 4001

[SwitchC-Bridge-Aggregation1] quit

3. Configure DCBX:

# Enable LLDP globally.

[SwitchC] lldp global enable

# Create Ethernet frame header ACL 4000.

[SwitchC] acl number 4000 name DCBX

# Configure the ACL to permit FCoE frames (protocol number is 0x8906) to pass through.

[SwitchC-acl-ethernetframe-4000] rule 0 permit type 8906 ffff

# Configure the ACL to permit FIP protocol packets (protocol number is 0x8914) to pass through.

[SwitchC-acl-ethernetframe-4000] rule 5 permit type 8914 ffff

[SwitchC-acl-ethernetframe-4000] quit

# Create a class named DCBX, with the operator of the class as OR.

[SwitchC] traffic classifier DCBX operator or

# Use ACL 4000 as the match criterion of the class.

Other manuals for HP FlexFabric 5700 series

Security Configuration Guide460 pages

Questions and Answers:

Need help?

Do you have a question about the HP FlexFabric 5700 series and is the answer not in the manual?

HP FlexFabric 5700 series Specifications

General

Layer Support	L2/L3
Routing Protocol	OSPF, BGP, RIP, IS-IS, Static Routing
Remote Management Protocol	SNMP, CLI, Web
Features	VXLAN
Compliant Standards	IEEE 802.1D, 802.1Q, 802.1w, 802.1s, 802.3ad
Operating Temperature	0°C to 45°C
Operating Humidity	10% to 90% (non-condensing)
VLANs	4K