To Next Page

To Previous Page

273

# Specify the remote IP address of the IPsec tunnel as 2.2.3.1.

[SwitchA-ipsec-policy-manual-map1-10] remote-address 2.2.3.1

# Configure inbound and outbound SPIs for ESP.

[SwitchA-ipsec-policy-manual-map1-10] sa spi outbound esp 12345

[SwitchA-ipsec-policy-manual-map1-10] sa spi inbound esp 54321

# Configure the inbound and outbound SA keys for ESP.

[SwitchA-ipsec-policy-manual-map1-10] sa string-key outbound esp simple abcdefg

[SwitchA-ipsec-policy-manual-map1-10] sa string-key inbound esp simple gfedcba

[SwitchA-ipsec-policy-manual-map1-10] quit

# Apply the IPsec policy map1 to interface VLAN-interface 1.

[SwitchA] interface vlan-interface 1

[SwitchA-Vlan-interface1] ipsec apply policy map1

2. Configure Switch B:

# Configure an IP address for VLAN-interface 1.

<SwitchB> system-view

[SwitchB] interface vlan-interface 1

[SwitchB-Vlan-interface1] ip address 2.2.3.1 255.255.255.0

[SwitchB-Vlan-interface1] quit

# Configure an ACL to identify data flows between Switch B and Switch A.

[SwitchB] acl number 3101

[SwitchB-acl-adv-3101] rule 0 permit ip source 2.2.3.1 0 destination 2.2.2.1 0

[SwitchB-acl-adv-3101] quit

# Create an IPsec transform set named tran1.

[SwitchB] ipsec transform-set tran1

# Specify the encapsulation mode as tunnel.

[SwitchB-ipsec-transform-set-tran1] encapsulation-mode tunnel

# Specify the security protocol as ESP.

[SwitchB-ipsec-transform-set-tran1] protocol esp

# Specify the ESP encryption and authentication algorithms.

[SwitchB-ipsec-transform-set-tran1] esp encryption-algorithm aes-cbc-192

[SwitchB-ipsec-transform-set-tran1] esp authentication-algorithm sha1

[SwitchB-ipsec-transform-set-tran1] quit

# Create a manual IPsec policy entry, with the policy name use1 and sequence number 10.

[SwitchB] ipsec policy use1 10 manual

# Apply ACL 3101.

[SwitchB-ipsec-policy-manual-use1-10] security acl 3101

# Apply IPsec transform set tran1.

[SwitchB-ipsec-policy-manual-use1-10] transform-set tran1

# Specify the remote IP address of the IPsec tunnel as 2.2.2.1.

[SwitchB-ipsec-policy-manual-use1-10] remote-address 2.2.2.1

# Configure the inbound and outbound SPIs for ESP.

[SwitchB-ipsec-policy-manual-use1-10] sa spi outbound esp 54321

[SwitchB-ipsec-policy-manual-use1-10] sa spi inbound esp 12345

# Configure the inbound and outbound SA keys for ESP.

Other manuals for HP FlexFabric 5700 series

Configuration Guide185 pages

Questions and Answers:

Need help?

Do you have a question about the HP FlexFabric 5700 series and is the answer not in the manual?

HP FlexFabric 5700 series Specifications

General

Layer Support	L2/L3
Routing Protocol	OSPF, BGP, RIP, IS-IS, Static Routing
Remote Management Protocol	SNMP, CLI, Web
Features	VXLAN
Compliant Standards	IEEE 802.1D, 802.1Q, 802.1w, 802.1s, 802.3ad
Operating Temperature	0°C to 45°C
Operating Humidity	10% to 90% (non-condensing)
VLANs	4K