EasyManuals Logo

HP Z210 User Manual

HP Z210
185 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #153 background imageLoading...
Page #153 background image
Table 6-9 POST error messages (continued)
Screen message Probable cause Recommended action
164—Memory Size Error Memory configuration is incorrect. 1. Run the Computer Setup (F10) Utility or the
Windows utilities.
2. Verify that the memory modules are installed
properly.
3. If third-party memory has been added, test the
memory configuration using HP memory.
4. Verify the memory module type.
201—Memory Error RAM failure. 1. Run the Computer Setup (F10) utility or the
Windows utilities.
2. Be sure that memory modules are installed
correctly.
3. Verify the memory module type.
4. Remove and replace memory modules one at a
time to isolate faulty modules.
5. Replace faulty memory modules.
6. If the error persists after replacing memory
modules, replace the system board.
202—Memory Type Mismatch Memory modules do not match. Replace the memory modules with matched sets.
203—Memory module failed
self-test and failing rank was
disabled
Defective memory module. Replace the memory module.
204—Memory module failed
and user rank was disabled
Improper module load. Reseat the memory module correctly.
205—Memory high
temperature detected
Insufficient memory module cooling. Verify that a memory module cooling fan is installed
and operating.
206—Memory setup invalid Memory configured incorrectly. Reconfigure the memory modules in the proper slots.
207—Incompatible DIMMs
detected
DIMMs are installed that do not fulfill
system requirements.
1. Verify that the memory module type matches
computer requirements.
2. Insert the DIMM in the proper memory socket.
3. Replace the DIMM if the problem persists.
208—Mismatched DIMMs
detected
Installed DIMMs are improperly
matched.
Verify that matching DIMMs are installed.
209—Memory warning
condition detected
Incorrect memory module type in use. Verify that the memory modules are compatible with
computer requirements.
212—Failed Processor 0 Processor has failed to initialize. 1. Reseat the processor in its socket.
2. If the processor does not respond, replace it.
3. Replace the system board.
ENWW
Diagnostic codes and errors
141

Table of Contents

Other manuals for HP Z210

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the HP Z210 and is the answer not in the manual?

HP Z210 Specifications

General IconGeneral
Tcase72.6 °C
Bus typeDMI
SteppingD2
FSB ParityNo
Processor cache6 MB
Processor cores4
Processor modelE3-1225
System bus rate5 GT/s
Processor seriesIntel Xeon E3-1200
Processor socketLGA 1155 (Socket H2)
Processor codenameSandy Bridge
Processor frequency3.1 GHz
Processor cache typeSmart Cache
Processor lithography32 nm
Processor manufacturerIntel
Processor front side bus- MHz
PCI Express slots version2.0
Processor boost frequency3.4 GHz
Processor operating modes64-bit
ECC supported by processorYes
Thermal Design Power (TDP)95 W
Number of processors installed1
CPU multiplier (bus/core ratio)31
Maximum number of PCI Express lanes20
Memory types supported by processorDDR3-SDRAM
Memory clock speeds supported by processor1066, 1333 MHz
Memory bandwidth supported by processor (max)21 GB/s
Maximum internal memory supported by processor32 GB
Graphics cardQuadro 600
Dimensions (WxDxH)100 x 381 x 338 mm
Networking featuresGigabit Ethernet (10/100/1000)
Graphics card familyNVIDIA
Maximum internal memory16384 MB
Graphics card manufacturerNvidia
Audio systemALC261
Product typeWorkstation
Motherboard chipsetIntel® C206
Memory slots4x DIMM
Internal memory8 GB
Memory channelsDual-channel
Memory clock speed1333 MHz
Memory layout (slots x size)- GB
HDD speed- RPM
RAID levels0, 1
HDD capacity500 GB
SSD capacity160 GB
HDD interfaceSATA II
SSD interfaceSATA
Optical drive typeDVD-RW
Total HDDs capacity1000 GB
Card reader integrated-
Number of HDDs installed2
Maximum graphics card memory1.024 GB
On-board graphics card modelIntel® HD Graphics P3000
On-board graphics card familyIntel® HD Graphics
On-board graphics card base frequency850 MHz
On-board graphics card dynamic frequency (max)1350 MHz
USB 2.0 ports quantity14
USB 3.2 Gen 1 (3.1 Gen 1) Type-A ports quantity0
Chassis typeSFF
Product colorBlack
Country of originChina
Compatible operating systemsWindows 7
Power supply240 W
CertificationENERGY STAR 5.0
Processor codeSR00G
Processor ARK ID52270
Processor package size37.5 x 37.5 mm
Supported instruction setsAVX, SSE4.1, SSE4.2
Intel Identity Protection Technology version1.00
Weight and Dimensions IconWeight and Dimensions
Depth381 mm
Width100 mm
Height338 mm
Weight7600 g

Related product manuals