[Switch B-rip-100] import-route rip 200
[Switch B-rip-100] quit
[Switch B] rip 200
[Switch B-rip-200] import-route rip 100
[Switch B-rip-200] quit
# View the routing table of Switch A after the routes are imported.
[Switch A] display ip routing-table
Route Flags: R - relay, D - download to fib
------------------------------------------------------------------------------
Routing Tables: Public
Destinations : 10 Routes : 10
Destination/Mask Proto Pre Cost Flags NextHop Interface
192.168.0.0/24 Direct 0 0 D 192.168.0.1 Vlanif50
192.168.0.1/32 Direct 0 0 D 127.0.0.1 Vlanif50
192.168.1.0/24 Direct 0 0 D 192.168.1.1 Vlanif10
192.168.1.1/32 Direct 0 0 D 127.0.0.1 Vlanif10
192.168.1.255/32 Direct 0 0 D 192.168.1.2 Vlanif10
192.168.2.0/24 RIP 100 4 D 192.168.1.2 Vlanif10
192.168.3.0/24 RIP 100 4 D 192.168.1.2 Vlanif10
192.168.4.0/24 RIP 100 4 D 192.168.1.2 Vlanif10
127.0.0.0/8 Direct 0 0 D 127.0.0.1 InLoopBack0
127.0.0.1/32 Direct 0 0 D 127.0.0.1 InLoopBack0
127.255.255.255/32 Direct 0 0 D 127.0.0.1 InLoopBack0
255.255.255.255/32 Direct 0 0 D 127.0.0.1 InLoopBack0
Step 5 Configure Switch B to filter the imported routes.
# Configure an ACL on Switch B and add a rule to the ACL. The rule denies the packets sent
from 192.168.4.0/24.
[Switch B] acl 2000
[Switch B-acl-basic-2000] rule deny source 192.168.4.0 0.0.0.255
[Switch B-acl-basic-2000] rule permit
[Switch B-acl-basic-2000] quit
# Configure Switch B to filter the route to 192.168.4.0/24 that is imported from RIP200 according
to the ACL rule.
[Switch B] rip 100
[Switch B-rip-100] filter-policy 2000 export
[Switch B-rip-100] quit
Step 6 Verify the configuration.
# View the RIP routing table of Switch A after the routes are filtered.
[Switch A] display ip routing-table
Route Flags: R - relay, D - download to fib
------------------------------------------------------------------------------
Routing Tables: Public
Destinations : 9 Routes : 9
Destination/Mask Proto Pre Cost Flags NextHop Interface
192.168.0.0/24 Direct 0 0 D 192.168.0.1 Vlanif50
192.168.0.1/32 Direct 0 0 D 127.0.0.1 Vlanif50
192.168.1.0/24 Direct 0 0 D 192.168.1.1 Vlanif10
192.168.1.1/32 Direct 0 0 D 127.0.0.1 Vlanif10
192.168.1.255/32 Direct 0 0 D 192.168.1.2 Vlanif10
192.168.2.0/24 RIP 100 4 D 192.168.1.2 Vlanif10
192.168.3.0/24 RIP 100 4 D 192.168.1.2 Vlanif10
127.0.0.0/8 Direct 0 0 D 127.0.0.1 InLoopBack0
127.0.0.1/32 Direct 0 0 D 127.0.0.1 InLoopBack0
S6700 Series Ethernet Switches
Configuration Guide - IP Routing 2 RIP Configuration
Issue 01 (2012-03-15) Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
56
To Next Page
Loading...
