Need help?Do you have a question about the Humminbird MEGA Live and is the answer not in the manual?
Details compatibility of MEGA Live Imaging TargetLock with control heads and trolling motors.
Lists necessary hardware and supplies for installation.
Instructions for checking current software versions on control heads.
Guide to update control head software using an SD card.
Guide to update accessory software via SD card.
Instructions for updating software using the FishSmart mobile app.
Steps to prepare the boat and trolling motor for installation.
Instructions for installing the mounting plate, options for single/dual mounts.
Steps for mounting and securing the control box.
Instructions for attaching the Landscape Mode mount to the shaft and transducer.
Guide on testing the Down, Forward, and Landscape modes of the transducer.
Steps to connect the shaft assembly to the mounting plate.
Instructions for installing the TargetLock Heading Sensor.
How to set correct transducer height, including propeller clearance.
Instructions for reinstalling the motor stabilizer after installation.
Steps for selecting a location and mounting the foot pedal.
Steps to prepare for MEGA 360 transducer installation.
Instructions for assembling the MEGA 360 mounting hardware.
Steps to install the MEGA 360 transducer pod.
How to set the correct height for the MEGA 360 pod.
Instructions for installing the collar clamp for the MEGA 360.
Instructions for routing the MEGA Live power, Ethernet, and heading sensor cables.
Guide for routing the MEGA Live control box cables.
Instructions for routing MEGA 360 accessory cables.
Steps for connecting the power supply to the transducer.
Verifying that the transducer and sensors are connected to the control head.
Instructions for configuring MEGA Live Imaging within the control head settings.
Steps to verify that the MEGA Live Imaging is functioning and displaying data.
Guide for pairing the TargetLock Heading Sensor with the control head.
Instructions on pairing the wireless foot pedal to the control head.
Procedure to calibrate the TargetLock Heading Sensor for accurate readings.
Verifying the operation of the optional GPS Heading Sensor.
Confirming baud rate and finalizing network setup.
Solutions for the "Out of the Water" error message.
Troubleshooting power failures and simulator mode issues.
Steps to resolve electrical noise or interference.
Details compatibility of MEGA Live Imaging TargetLock with control heads and trolling motors.
Lists necessary hardware and supplies for installation.
Instructions for checking current software versions on control heads.
Guide to update control head software using an SD card.
Guide to update accessory software via SD card.
Instructions for updating software using the FishSmart mobile app.
Steps to prepare the boat and trolling motor for installation.
Instructions for installing the mounting plate, options for single/dual mounts.
Steps for mounting and securing the control box.
Instructions for attaching the Landscape Mode mount to the shaft and transducer.
Guide on testing the Down, Forward, and Landscape modes of the transducer.
Steps to connect the shaft assembly to the mounting plate.
Instructions for installing the TargetLock Heading Sensor.
How to set correct transducer height, including propeller clearance.
Instructions for reinstalling the motor stabilizer after installation.
Steps for selecting a location and mounting the foot pedal.
Steps to prepare for MEGA 360 transducer installation.
Instructions for assembling the MEGA 360 mounting hardware.
Steps to install the MEGA 360 transducer pod.
How to set the correct height for the MEGA 360 pod.
Instructions for installing the collar clamp for the MEGA 360.
Instructions for routing the MEGA Live power, Ethernet, and heading sensor cables.
Guide for routing the MEGA Live control box cables.
Instructions for routing MEGA 360 accessory cables.
Steps for connecting the power supply to the transducer.
Verifying that the transducer and sensors are connected to the control head.
Instructions for configuring MEGA Live Imaging within the control head settings.
Steps to verify that the MEGA Live Imaging is functioning and displaying data.
Guide for pairing the TargetLock Heading Sensor with the control head.
Instructions on pairing the wireless foot pedal to the control head.
Procedure to calibrate the TargetLock Heading Sensor for accurate readings.
Verifying the operation of the optional GPS Heading Sensor.
Confirming baud rate and finalizing network setup.
Solutions for the "Out of the Water" error message.
Troubleshooting power failures and simulator mode issues.
Steps to resolve electrical noise or interference.
General| Connectivity | Ethernet |
|---|---|
| Technology | MEGA Imaging |
| Mounting Options | Transom, Trolling Motor |
| Cable Length | 20 feet |
| Transducer Mount Location | Transom |
| Display Resolution | N/A (External display required) |
| Screen Size | N/A (External display required) |
To Next Page
