Figures
1. Rear view of file module ........24
2. File module node Ethernet network
connections. ............26
3. Diagram shows how to connect the file
modules to the control enclosure using Fibre
Channel cables. (A) is file module 1 and (B) is
file module 2. (C) is the control enclosure. . . 31
4. LEDs on the power supply units of the control
enclosure .............43
5. LEDs on the node canisters .......45
6. Selecting a file module to display node status 58
7. Displaying node status .........59
8. Example that shows that mirroring is
re-synchronizing ...........61
9. Example that shows that a drive is not
synchronized ............62
10. Example that shows that the mirror is not
created ..............63
11. Example of a SMART error .......64
12. Removing the Ethernet adapter .....107
13. Location of the rubber stopper on the chassis 108
14. Location of the Ethernet adapter filler panel
on the chassis ...........108
15. Location of the port openings on the chassis 109
16. Aligning the Ethernet adapter port connectors
with the port openings ........109
17. Side view of adapter in the server.....110
18. Port connector alignment .......110
19. 16-drive-capable server model ......112
20. Tape-enabled server model .......112
21. SAS riser-card and controller assembly on the
16–drive-capable server model ......113
22. Controller retention brackets on
16-drive-capable server model ......114
23. SAS controller front retention brackets 114
24. Removing the rear controller retention bracket 115
25. Installing the controller retention bracket 115
26. Sliding the controller retention bracket inward
and pressing the release tab .......116
27. SAS riser-card assembly on tape-enabled
server model ............116
28. ServeRAID M1000 advanced feature key and
M1015 adapter ...........121
29. ServeRAID M5000 advanced feature key and
M5014 adapter ...........122
30. ServeRAID M1000 advanced feature key and
M1015 adapter ...........123
31. ServeRAID M5000 advanced feature key and
M5014 adapter ...........124
32. Releasing the battery retention clip ....125
33. Disconnecting the remote battery cable 125
34. Removing the battery from the battery carrier 126
35. Connecting the remote battery cable ....127
36. Locating the posts on the battery and battery
carrier ..............127
37. DIMM locations for the Storwize V7000
Unified System x3650 M2 server .....131
38. DIMM locations for the Storwize V7000
Unified System x3650 M3 server .....132
39. Heat-sink release lever ........141
40. Microprocessor release latch ......142
41. Aligning the microprocessor ......144
42. Bottom surface of the heat sink .....146
43. Aligning the heat sink above the
microprocessor ...........146
44. 240 VA safety cover .........154
45. 240 VA safety cover .........155
46. Management GUI showing CTDB status for
both file modules ..........161
47. LEDs on the power supply units of the
control enclosure ..........199
48. LEDs on the node canisters .......201
49. LEDs on the node canisters .......207
50. Rear of node canisters that shows the
handles. .............210
51. Removing the canister from the enclosure 210
52. Rear of expansion canisters that shows the
handles. .............212
53. Removing the canister from the enclosure 212
54. SFP transceiver ...........213
55. Directions for lifting the handle on the power
supply unit ............216
56. Using the handle to remove a power supply
unit ...............216
57. Directions for lifting the handle on the power
supply unit ............220
58. Using the handle to remove a power supply
unit ...............220
59. Removing the battery from the control
enclosure power-supply unit ......224
60. Unlocking the 3.5" drive ........226
61. Removing the 3.5" drive ........226
62. Unlocking the 2.5" drive ........227
63. Removing the 2.5" drive ........228
64. SAS cable .............229
65. Removing a rail assembly from a rack cabinet 237
© Copyright IBM Corp. 2011, 2012 vii
|
||
To Next Page
Loading...
Need help?
General
