Icom IC-756PRO2 - Page 83

81
13
CONTROL COMMAND
•Command table (continued)
Command Sub command Description
1A 0547 Send/read cut number style
(0=Normal, 1=190→ANO,
2=90→ON, 3=190→ANT,
4=90→NT)
0548 Send/read count up trigger chan-
nel (1=M1, 2=M2, 3=M3, 4=M4)
0549 Send/read present number
(1–9999)
0550 Send/read CW keyer repeat time
(1=1 sec. to 60=60 sec.)
0551 Send/read CW keyer dot/dash
ratio (28=1:1:2.8 to 45=1:1:4.5)
0552 Send/read rise time (0=2 msec.,
1=4 msec., 2=6 msec., 3=8 msec.)
0553 Send/read paddle polarity
(0=Normal, 1=Reverse)
0554 Send/read keyer type (0=Straight,
1=Bug-key, 2=ELEC-Key)
0555 Send/read mic. up/down keyer set
(0=OFF, 1=ON)
0556 Send/read scan speed (0=low,
1=high)
0557 Send/read scan resume (0=OFF,
1=ON)
0558 Send/read VOX gain (0=0% to
255=100%)
0559 Send/read anti VOX gain (0=0% to
255=100%)
0560 Send/read VOX delay (0=0.0 sec.
to 20=2.0 sec.)
0561 Send/read RTTY filter bandwidth
(0=250 Hz, 1=300 Hz, 2=350 Hz,
3=500 Hz, 4=1 kHz)
0562 Send/read twin peak filter (0=OFF,
1=ON)
0563 Send/read timer functions (0=OFF,
1=ON)
0564 Send/read DSP filter type
(0=SSB: sharp; CW: sharp,
1=SSB: sharp; CW: soft,
2=SSB: soft CW: sharp,
3=SSB: soft CW: soft)
0565 Send/read quick RIT/∂TX clear
function (0=OFF, 1=ON)
0566 Send/read SSB/CW synchronous
tuning function (0=OFF, 1=ON)
0567 Send/read CW normal side set
(0=LSB, 1=USB)
0568 Send/read external keypad type
(0=OFF, 1=Keyer send, 2=Voice
play (Tx), 3=Auto)
0569 Send/read NB level (0=0% to
255=100%)
06 Send/read DATA mode (0=OFF,
1=ON)
07 Send/read SSB transmit band-
width (0=Wide, 1=Middle, 2=Nar-
row)
1B 00 Set repeater tone frequency
01 Set tone squelch tone frequency
1C 00 Set the transceiver to receive or
transmit condition (0=Rx; 1=Tx)
Command Sub command Description
1A 0518 Send/read power-OFF period
(5=5 min. to 120=120 min. in
5 min. step)
0519 Send/read calibration marker
(0=OFF, 1=ON)
0520 Send/read confirmation beep
(0=OFF, 1=ON)
0521 Send/read band edge beep
(0=OFF, 1=ON)
0522 Send/read RF/SQL control set
(0=Auto, 1=SQL, 2=RF+SQL)
0523 Send/read quick dualwatch set
(0=OFF, 1=ON)
0524 Send/read quick split set (0=OFF,
1=ON)
0525 Send/read FM split offset (HF)
–4.000 to +4.000 MHz
(see p. 82 for details)
0526 Send/read FM split offset (50 MHz)
–4.000 to +4.000 MHz
(see p. 82 for details)
0527 Send/read split lock set (0=OFF,
1=ON)
0528 Send/read tuner auto start set
(0=OFF, 1=ON)
0529 Send/read PTT tune set (0=OFF,
1=ON)
0530 Send/read antenna selection
(0=OFF, 1=Manual, 2=Auto)
0531 Send/read RTTY mark frequency
(0=1275 Hz, 1=1615 Hz,
2=2125 Hz)
0532 Send/read RTTY shift width
(0=170 Hz, 1=200 Hz, 2=425 Hz)
0533 Send/read RTTY keying polarity
(0=Normal, 1=Reverse)
0534 Send/read RTTY decode USOS
(0=OFF, 1=ON)
0535 Send/read RTTY decode new line
code (0=CR,LF,CR+LF,
1=CR+LF)
0536 Send/read speech language
(0=English, 1=Japanese)
0537 Send/read speech speed (0=slow,
1=fast)
0538 Send/read S-level speech (0=OFF,
1=ON)
0539 Send/read memo pad numbers
(0=5 ch, 1=10 ch)
0540 Send/read main dial auto TS
(0=OFF, 1=Low, 2=High)
0541 Send/read mic. up/down speed
(0=Low, 1=High)
0542 Send/read CI-V transceive set
(0=OFF, 1=ON)
0543 Send/read CI-V 731 mode set
(0=OFF, 1=ON)
0544 Send/read TX spectrum scope set
(0=OFF, 1=ON)
0545 Send/read spectrum scope max.
hold set (0=OFF, 1=ON)
0546 Send/read voice auto monitor set
(0=OFF, 1=ON)