EasyManuals Logo

Industrial Data Systems IDS 440 User Manual

Industrial Data Systems IDS 440
75 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #4 background imageLoading...
Page #4 background image
Parameter 10. Primary Units Type (1 [lb])......................................................................29
Parameter 11. Decimal Point Position (0 [no decimal point]).........................................29
Parameter 12. Count-by (1)............................................................................................29
Parameter 13. Alternate Units Type (2 [kg])...................................................................30
Parameter 14. Alternate Decimal Point (1).....................................................................30
Parameter 15. Alternate Count-by (5) ............................................................................30
Parameter 16. Alt Units Conversion Factor (45,360) .....................................................30
Parameter 17. Full Scale Graduations (10,000).............................................................31
Parameter 18. Overload Graduations (10,200) ..............................................................31
Parameter 19. Deadload Offset........................................................................................31
Parameter 20. Disable Power-On Zero (1 [disabled]) ......................................................31
Parameter 21. Deadload Factor .......................................................................................31
Parameter 22. Weight Conversion Factor .......................................................................31
Serial I/O Ports.........................................................................................................................32
Parameter 23 Serial Port 1 Mode (4 [8 data bits, no parity])...........................................32
Parameter 24 Serial Port 1 Baud Rate (1 [9600 baud]) ..................................................32
Parameter 25 Serial Port 2 Mode (4 [8 data bits, no parity])...........................................33
Parameter 26 Serial Port 2 Baud Rate (1 [9600 baud]) ..................................................33
Parameter 27 TX2 Control / Station ID (255 [single station]) ........................................33
Parameter 28 TX2 Format (2 Condec format).................................................................34
Printer Parameters ...................................................................................................................35
Parameter 29 Printer Port Select (2 [Serial Port 1]) ........................................................35
Parameter 30 Auto Print LF after CR (1 [yes]) ................................................................35
Parameter 31 End of Print Character (12 [form feed]) ....................................................35
Parameters 32, 33 34, 84, 85, 86, 87, 88, 89 and 90 Print Labels ...................................35
Parameters 35, 36, 37, and 38: Print Codes .....................................................................36
Parameter 39 Enable TTL Remote Control (1 [enabled]) ...............................................36
Display Intensity, Battery, Watch Dog Timer ...........................................................................36
Parameter 40 Display Intensity (10) ................................................................................36
Parameter 41 Battery Backup (0 [no])..............................................................................36
Parameter 42 Enable Watch Dog Timer (0 [no]) .............................................................36
Parameters 43-50 Fixed Registers ........................................................................................36
Parameters 51-58 Keyboard Event Functions .........................................................................37
Parameter Functions ........................................................................................38
Parameter Functions................................................................................................................38
Access Parameter Functions ...................................................................................................39
Function 59 Display Calibration Audit Number. .......................................................................39
Function 60 Calibrate Scale - Deadload First ..........................................................................40
Function 61 Calibrate Scale - Span First .................................................................................40
Function 62 Calibrate Deadload Only ......................................................................................40
Function 63 Adjust Gain Calibration ........................................................................................41
Adjust Gain – 5 Point Linearization ...................................................................................41
Function 64 Configure Passwords ...........................................................................................42
Function 65 Configure Print Formats .......................................................................................43
Modify or Design a Print Format........................................................................................43
Function 66 Set Time and Date ...............................................................................................47
Function 67 Display Operation Parameters .............................................................................47
Function 68 Print Operation Parameters .................................................................................47
Function 69 Diagnostic Tests...................................................................................................48
Function 70 Initialize Operation Parameters to Factory Defaults ............................................48
Function 71 Configure Event Monitor ......................................................................................49
Function 72 Scale Basic Function Editor .................................................................................49
Function 73 Initialize Function Memory ...................................................................................49
Function 74 Configure Timers..................................................................................................50

Table of Contents

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Industrial Data Systems IDS 440 and is the answer not in the manual?

Industrial Data Systems IDS 440 Specifications

General IconGeneral
BrandIndustrial Data Systems
ModelIDS 440
CategoryAccessories
LanguageEnglish

Related product manuals