How to fix a black screen on my InFocus INF8630eAG Monitor?
To resolve a black screen issue on your InFocus Monitor, ensure that both ends of the power cord are securely connected, the system power switch is turned on, and the display itself is also powered on. Additionally, verify that the outlet is providing the correct voltage using a voltmeter.
Why is my InFocus Monitor remote not working?
If your InFocus Monitor remote isn't working, check the following: ensure the display is turned on and you press the power button on the remote. Verify the batteries are correctly situated in the remote and are fresh (note that batteries are not included). Try replacing the batteries with new ones. Aim the remote towards the lower right edge of the panel where the sensor is located, at an angle between 26 and 30 degrees both vertically and horizontally. Also, make sure there are no obstructions blocking the sensor.
What to do if there is no image on my InFocus INF8630eAG Monitor?
If your InFocus Monitor has power but no image is displayed, verify that the cables, cords, and connections are in good condition. Also, ensure that the correct input source is selected and that the input signal is compatible with the display.
Why is there no sound from external speakers connected to my InFocus INF8630eAG Monitor?
If you're not getting sound from external speakers connected to your InFocus Monitor, please verify the following: the speakers are properly connected and their power switch is on; an audio cable is correctly installed between the external device and the display; 'Mute' is not active (test the Mute button on the remote); and the volume is turned up. Note that an HDMI 1.3 (or higher) source and source device are required to hear audio via the HDMI cable.
How to fix incorrect colors on my InFocus INF8630eAG Monitor display?
To correct the colors on your InFocus Monitor display, try the following: adjust the color settings in the Picture menu, or reset the picture settings. Also, verify that connections between the source and the display have been made correctly, that cables, cords, and connections are in good condition, and that the correct input source is selected and the input signal is compatible with the display.
Why does my InFocus INF8630eAG Monitor shut down suddenly?
If your InFocus Monitor shuts down suddenly, it may have overheated. Verify that a source is active and remove any objects blocking the vents.
Why is there no sound from the internal speakers on my InFocus Monitor?
If there is no sound from the internal speakers on your InFocus Monitor, verify that the volume is turned up and the sound has not been muted from the remote control. Also, for video viewing, verify that the playback has not been paused and that the video’s audio has not been muted.
What to do if the InFocus INF8630eAG touch screen is not responding?
If the display screen of your InFocus Monitor does not respond to touch gestures, press the Total Touch Control button on the bottom right front of the display to turn on touch control. If this doesn't work, cycle the power by turning off the display, waiting a few seconds, and then turning it back on.
What does 'No Signal' mean on my InFocus INF8630eAG?
The 'No Signal' message on your InFocus Monitor indicates that it's looking for a connected video source. Connect the monitor to any video source such as a VHS, Apple TV, or external PC.
Why is there feedback noise from the InFocus INF8630eAG Monitor speakers?
Feedback noise from the speakers of your InFocus Monitor can occur when infrared communication equipment (for example, infrared cordless headphones) is used near the display. Move the infrared communication equipment away from the display.
General| Screen Size | 86 inches |
|---|---|
| Resolution | 3840 x 2160 (4K UHD) |
| Contrast Ratio | 1200:1 |
| Response Time | 8 ms |
| Touch Technology | Infrared |
| Touch Points | 20 |
| Operating System | Android 8.0 |
| Speakers | Yes |
| Aspect Ratio | 16:9 |
| Viewing Angle | 178° |
| Connectivity | HDMI, USB, VGA, RS232 |
| Weight | 67 kg |
| Brightness | 350 cd/m² |
| Display Colors | 1.07B (10 bit) |
| Speaker Power | 2 x 10W |
To Next Page
