How to fix InFocus X17 that does not turn on?
If your InFocus Projector doesn't turn on, first ensure the power cord is securely plugged into both the projector's AC inlet and a working power outlet, and that the outlet switch is on. Also, if the projector was recently turned off, it may be in the cooling down process. Wait until this process is complete before attempting to turn it on again.
What to do if my InFocus X17 Projector has no picture?
If your InFocus Projector shows no picture, first ensure that the video source is turned on and the signal cable is correctly connected. Check the connection between the projector and the input signal device. Make sure the correct input signal is selected using the SOURCE key on the projector or remote. Also, verify that the lens cover is open.
How to fix a blurred image on InFocus X17?
If your InFocus Projector image is blurred, adjust the focus of the lens using the focus ring. Also, adjust the projection angle, direction, and height of the unit to properly align the projector and the screen. Ensure that the lens cover is open.
Why doesn't my InFocus X17 remote control work?
If the InFocus Projector remote control isn't working, first replace the battery with a new one. Ensure there are no obstacles between the remote and the projector. Also, make sure you are within 8 meters (26 feet) of the projector.
Explains the purpose and operation of buttons on the projector and remote control.
Guides users on selecting the best placement for the projector based on room layout and setup.
Explains factors affecting image size and how to achieve optimal projection dimensions.
Provides a table with screen sizes, projection distances, and vertical offsets for setup.
Details how to connect the projector to a computer or monitor using VGA and audio cables.
Explains how to connect various video sources like Component, S-Video, and Composite.
Step-by-step guide on powering on the projector, including initial checks and settings.
Explains how to navigate and use the projector's On-Screen Display (OSD) menus for adjustments.
Details how to set, change, and manage the projector's password security feature.
Describes how to select different input sources for the projector and auto-search functionality.
Covers adjusting projection angle, height, and using auto-adjustment for optimal picture quality.
Provides causes and remedies for issues related to the projector failing to power on.
Lists common causes for a blank screen and offers solutions for image display problems.
Addresses issues causing a blurred image and suggests steps for correction.
Explains troubleshooting steps for a non-functional remote control, such as battery or obstacles.
Guides users on how to handle incorrect password entries and recall procedures.
General| Matrix size | 0.55 \ |
|---|---|
| Projection distance | 1.49/6 m |
| Vertical scan range | 56 - 85 Hz |
| Horizontal scan range | 31.35 - 68.7 kHz |
| Projection technology | DLP |
| Contrast ratio (typical) | 2000:1 |
| Screen size compatibility | 0.69 - 6.4 \ |
| Projector native resolution | XGA (1024x768) |
| Keystone correction, vertical | -30/30 ° |
| Aspect ratio | 4:3, 5:4, 16:9 |
| RS-232 ports | 1 |
| Dimensions (WxDxH) | 223.5 x 263.9 x 111.8 mm |
| Power requirements | 100 - 240 V, 50 - 60 Hz |
| Throw ratio | 1.9 - 2.1:1 |
| Lamp power | 140 W |
| Light source type | Lamp |
| Service life of light source (economic mode) | 4000 h |
| Analog signal format system | NTSC, PAL, SECAM |
| RMS rated power | 5 W |
| Serial interface type | RS-232 |
| Noise level | 29 dB |
| Power consumption (typical) | 285 W |
| Operating temperature (T-T) | 5 - 35 °C |
| Placement | Ceiling |
Weight and Dimensions| Weight | 2400 g |
|---|
To Next Page
