TEMPERATURE/RESISTANCE CHART
IF COMPRESSOR THEN
A. Has Auto Start/Stop Prom No Changes Required
B. Does Not Have Auto Start/ Install Auto Start/Stop
Stop Prom Field Kit 39666672
TOOLS REQUIRED:
ONLY WHAT WOULD BE FOUND IN ANY REASONABLY EQUIPPED
SERVICEMAN’S TOOL BOX.
PARTS LIST (KIT P/N 39674387)
ITEM PART NUMBER QTY DESCRIPTION
1 39813274 1 INTERFACE I, SEQUENCER
2 39547880 1 CABLE, MODULAR, 44" LG.
3 39177357 4 SCREW, #10-32 SELF TAPPING
4 39178611 4 SCREW, #10-24
5 39128533 4 NUT, #10-24
6 APDD 403A-91 1 INSTRUCTIONS, INTERFACE I
INSTALLATION
7 APDD 405A-91 1 INSTRUCTIONS, SEQUENCE
CONTROLLER, SSR 10-450 HP
8 39181284 1 FUSE, 1A (SPARE)
SUBJECT: TESTING SOFTWARE WITH A SEQUENCER
Connect a sequencer to a compressor. Follow the following steps for testing
software with a sequencer.
1) Start the compressor.
2) Put the compressor into the ON/OFF LINE mode.
3) Set the sequencer to load and unload at pressures lower than the current
settings of the controller.
4) Start the sequencer. The unit should begin to load and unload at the
sequencer’s pressure settings.
5) Stop the sequencer. The unit should load and unload at the controller’s
pressure settings.
6) Start the sequencer. The unit should begin to load and unload at the
sequencer’s pressure settings.
7) Disconnect the sequencer. The unit should load and unload at the
controller’s pressure settings.
8) Connect the sequencer. The unit should load and unload at the
sequencer’s pressure settings.
If the unit has AUTO START/STOP, do steps 9 and 10.
9) Close discharge valve so the unit will unload. Wait for the amount of time
that the auto restart timer is set for. When this time has expired, the unit
should shut off.
10) Open the discharge valve. The line pressure should drop and the unit
should restart. The unit should load and unload at the sequencer’s
pressure settings.
11) Stop the sequencer and the compressor.
52 19171
53 18658
54 18161
55 17679
56 17211
57 16757
58 16317
59 15889
60 15475
61 15072
62 14681
63 14301
64 13933
65 13575
66 13227
67 12890
68 12562
69 12244
70 11934
71 11634
72 11342
73 11058
74 10782
75 10514
76 10254
77 10000
78 9754
79 9515
80 9282
81 9055
82 8835
83 8621
84 8413
85 8210
86 8013
87 7821
88 7635
89 7453
90 7277
91 7105
92 6937
93 6774
94 6616
95 6461
96 6311
97 6165
98 6022
99 5883
100 5748
101 5616
102 5488
103 5363
104 5241
105 5123
106 5007
107 4894
108 4784
109 4677
110 4573
111 4472
112 4372
113 4276
114 4182
115 4090
116 4000
117 3913
118 3828
119 3745
120 3663
121 3584
122 3507
123 3432
124 3359
125 3287
126 3218
127 3150
128 3083
129 3019
130 2955
131 2894
132 2833
133 2775
134 2717
135 2661
136 2607
137 2553
138 2501
139 2450
140 2400
141 2352
142 2304
143 2258
144 2213
145 2169
146 2125
147 2083
148 2042
149 2001
150 1962
151 1924
152 1888
153 1849
154 1813
155 1778
-38-
-37-
DEGREE
F. TEMP. RES.
0 89768
1 86914
2 84161
3 81503
4 78938
5 76463
6 74072
7 71765
8 69536
9 67384
10 65306
11 63298
12 61359
13 59485
14 57674
15 55924
16 54233
17 52598
18 51017
19 49490
20 48012
21 46584
22 45202
23 43865
24 42573
25 41322
26 40112
27 38941
28 37808
29 36712
30 35650
31 34623
32 33631
33 32668
34 31736
35 30834
36 29960
37 29114
38 28295
39 27501
40 26733
41 25988
42 25267
43 24568
44 23891
45 23235
46 22599
47 21983
48 21385
49 20806
50 20244
51 19699
DEGREE
F. TEMP. RES.
DEGREE
F. TEMP. RES.