Inovance MD280NT2.2GB - Use of DI Terminals; Use of DO Terminals

Operation and Display MD280 User Manual
- 70 -
Figure 4-28 Switchover between motor 1 and motor 2
F2-00
F2-01
F2-02
F2-03
F2-04
.
.
.
32
.
.
Switch for motor
switchover
Terminal
Function
code
Setting
value
DI1
DI2
DI3
DI4
DI5
COM
K1
Stop state
Motor 1 Motor 2
MD280
Q1
K1 linked with Q1
4.8 Use of DI Terminals
7KHFRQWUROERDUGSURYLGHV¿YH',WHUPLQDOV',WR',
7KHLQWHUQDOKDUGZDUHRI',WHUPLQDOVLVFRQ¿JXUHGZLWK9'&SRZHUVXSSO\IRUGHWHFWLRQ
You can input a signal to a DI terminal of the AC drive only by shorting the DI terminal and
COM.
%\GHIDXOWD',WHUPLQDOLVDFWLYHORJLFZKHQEHLQJVKRUWHGZLWK&20DQGLQDFWLYHORJLF
ZKHQEHLQJQRWVKRUWHGZLWK&20
<RXFDQFKDQJHWKH',WHUPLQDODFWLYHPRGH7KDWLVD',WHUPLQDOLVLQDFWLYHORJLFZKHQ
VKRUWHGZLWK&20DQGDFWLYHORJLFZKHQQRWVKRUWHGWR&206HWWKHDFWLYHPRGHLQ)
ELWWRELWLQWKHYDOXHRIWKLVIXQFWLRQFRGHHVSHFWLYHO\VSHFLI\WKHDFWLYHPRGHVHWWLQJ
RI',WR',VHWWKHFRUUHVSRQGLQJELWWRDQGFRYHUWWKHELQDU\YDOXHWRDGHFLPDOYDOXH
7KH$&GULYHDOVRSURYLGHV)',ILOWHU WLPHIRUWKH',VLJQDOWRLPSURYHWKHDQWL
interference level.
The five DI terminals can be defined in function codes F2-00 to F2-04. Each DI can be
allocated with their respective function from the 33 functions. For details, see descriptions of
F2-00 to F2-04.
The hardware design allows only DI5 to receive high-speed pulse signal. If high-speed pulse
count is required, use DI5.
4.9 Use of DO Terminals
7KH0'SURYLGHVDPXOWLIXQFWLRQ )0WHUPLQDO)03$2RU'2D UHOD\RXWSXW
WHUPLQDODQGWZR'2WHUPLQDOV'2DQG'2)0'2DQG'2DUHWUDQVLVWRURXWSXWV
and can drive 24 VDC low-voltage circuit; TA/TB/TC is relay output, and can drive 250 VAC
control circuit.
6HWWKHIXQFWLRQRIWKHPXOWLIXQFWLRQ)0WHUPLQDO)03$2RU'2RQO\RQHIXQFWLRQFDQ
EHHQDEOHGHDFKWLPHLQ ):KHQWKH)0WHUPLQDOLVXVHGDV'2WKHXVDJHLVWKH
same as that of DO1 and DO2. When F3-00 is set to 0, the FM terminal provides high-
speed pulse output, indicating the values of internal running parameters. The highest pulse
frequency is 50 kHz. For details, see the descriptionof F3-05.
The relay output terminals are TA/TB/TC, where TA is the common terminal, TB is a normally
efesotomasyon.com