Advanced Operations
En-80
This setting determines what the volume will be for
Zone 2/3/4 each time the AV receiver is turned on.
To use the same volume level as when the AV receiver was
last turned off, select “Last”.
The “Zone 2 Power On Volume”, “Zone 3 Power On
Volume”, and “Zone 4 Power On Volume” cannot be set
higher than the “Zone 2 Maximum Volume”, “Zone 3
Maximum Volume”, and “Zone 4 Maximum Volume”
setting.
Tuner
■ AM/FM Frequency Step (North American
models)
` 10kHz/200kHz
:
` 9kHz/50kHz:
Select the frequency step according to your area.
■ AM Frequency Step (Australian models)
` 10kHz:
` 9kHz
:
Select the frequency step according to your area.
For AM/FM tuning to work properly, you must specify the
AM/FM frequency step used in your area.
Note
• When this setting is changed, all radio presets will be deleted.
HDMI
■ HDMI Control(RIHD)
` Off
` On
Turn this setting on to allow
p-compatible
components connected via HDMI to be controlled by the
AV receiver (➔ page 112).
Note
• When the setting is set to “On” and the menu is closed, the names
of connected p-compatible components and “RIHD On”
are displayed on the AV receiver.
“Search…” → “(name)” → “RIHD On”
When the AV receiver cannot receive the name of the component,
it is displayed as “Player
*
” or “Recorder
*
”, etc. (“
*
” shows up
and indicates the number of components, when two or more are
received).
• When an p-compatible component is connected to the
AV receiver via an HDMI cable, the name of the connected
component is displayed on the AV receiver display. For example,
while you are watching TV broadcasting, if you operate a Blu-ray
Disc/DVD player (being powered on) with the remote control of
the AV receiver, the name of the Blu-ray Disc/DVD player will
be displayed on the AV receiver.
• Set it to
“Off” when a connected piece of equipment is not
compatible or it is unclear whether the equipment is compatible
or not.
• If operation is not normal when set to
“On”, change the setting to
“Off”.
• Refer to the connected component’s instruction manual for
details.
• When the “HDMI Control(RIHD)” setting is set to “On”, the
power consumption on standby mode slightly increases.
(Depending on the TV status, the AV receiver will enter standby
mode as usual.)
• The HDMI component (connected to HDMI IN 1/2/3/AUX
Input) selected for Zone 2 cannot be operated with the remote
controller through the AV receiver using RIHD function and also
cannot be operated on the TV connected to HDMI OUT MAIN
using CEC function.
• The HDMI component (connected to HDMI IN 1/2/3/AUX
Input) selected for Zone 2 can be operated on the TV in Zone 2
using CEC function.
• When the source equipment is connected with the u
connection, it may malfunction if “HDMI Control(RIHD)” is
set to “On”.
■ HDMI Through
` Off
` BD/DVD, CBL/SAT, STB/DVR, GAME1, GAME2,
PC, AUX, TV/CD, PHONO:
Selects the input source for which the HDMI
Through function is enabled.
` Last:
The HDMI Through function is activated on the input
source selected at the time of setting the AV receiver
to standby mode.
When enabling the HDMI Through function, regardless of
whether the AV receiver is on or in standby, both audio
and video streams from an HDMI input will be output to
the TV or other components via HDMI connection. The
HDMI indicator will be dimly-lit in standby mode. Note
that the indicator may not light under certain conditions
(
➔ page 58).
This setting is fixed to “Auto” automatically when the
above “HDMI Control(RIHD)” setting is set to “On”,
resulting in automatic input source selection.
Note
• Only an input source assigned to an HDMI IN via “HDMI Input”
setting is enabled (➔ page 60).
• The power consumption in standby mode will increase during the
HDMI Through function; however in the following cases, the
power consumption can be saved:
– The TV is in standby mode.
– You are watching a TV program.
• Refer to the connected component’s instruction manual for
details.
• Depending on the connected component, the correct input source
may not be selected with the setting fixed to “Auto”.
• This setting is set to “Off” automatically when the “HDMI
Control(RIHD)” setting is set to “Off”.
• This function is only available for the HDMI OUT MAIN jack.
To Next Page
Loading...
