To Next PageTo Next PageWhy doesn't the heater work in my Jackson TempStar Dishwasher?
If the wash or rinse heater isn't working in your Jackson Dishwasher, check the heater element for continuity; if it's open, replace the heater. Also, replace the heater contactor and verify the operation and settings of the thermostats, replacing them if necessary.
What to do if my Jackson TempStar Dishwasher doesn’t drain when turned off?
If your Jackson Dishwasher isn’t draining when you switch it off, here’s what to do: * Check for and remove any drain clogs. * Remove the standpipe and run the drain cycle again.
Why are the dishes not coming clean in my Jackson Dishwasher?
To address dishes not coming clean in your Jackson Dishwasher, first, ensure that the incoming water, rinse water, and wash water temperatures meet the minimum requirements specified on the machine's data plate. Next, adjust the detergent concentration to match the water volume in the machine. Finally, if you're using a solid dispenser, check and replace the canister if it's empty.
Why does my Jackson Dishwasher run continuously in the wash cycle?
If your Jackson Dishwasher runs continuously in the wash cycle, it might be in delime mode. Change the operation mode from DELIME to NORMAL. If that's not the issue, the wash cycle delay timer could be faulty. If the red light isn't on during cycles B, C, or D, replace the cycle timer. Also, ensure the delay potentiometer is correctly adjusted for cycles B, C, or D. A faulty cam timer could also be the cause; in this case, also adjust the delay potentiometer for cycles B, C, or D. Confirm that the wash cycle delay timer is functioning correctly, that the timer motor is receiving power, and that there are no obstructions limiting the rotation of the cam timer.
What to do if my Jackson TempStar will not fill after the door is closed, but the power is on?
If the Jackson Dishwasher will not fill after the door is closed but the power light is on, the rinse solenoid valve may be faulty, requiring repair or replacement. Another potential cause is a faulty door switch; verify its wiring, and if correct, replace the switch. Lastly, a fouled or faulty high-level probe could be the issue; clean the probe, and if it's still not working after cleaning, replace it.
Why does my Jackson Dishwasher fill slowly and/or have a weak rinse?
If your Jackson Dishwasher fills slowly or the rinse is weak, here's what to investigate: * Clean any clogged or obstructed rinse arms by removing them. * Adjust the water pressure regulator to ensure a flow of 10 ± 2 PSI. * Clean out the Y-strainer.
What to do if my Jackson TempStar won't run but the power light is on?
If your Jackson Dishwasher won't run after closing the door, but the power light is on and it's filling, consider these possibilities: * The timer might be faulty. Verify it's receiving power; if it is, replace the timer assembly. * The wash motor could be faulty or damaged. Check if it's getting power; if it is, replace the motor. * The wash motor contactor might be faulty. Check for continuity; if the contacts are open, replace the contactor.
Why is the wash or rinse heater not working in my Jackson Dishwasher?
If your Jackson Dishwasher's wash or rinse heater isn't working, try these solutions: * Check the heater element for continuity; if it's open, replace the heater. * Replace the heater contactor if it's faulty. * Verify the operation and settings of the thermostats; replace them if necessary.
Why is there water leaking at the wash pump of my Jackson Dishwasher?
If water is leaking at the wash pump of your Jackson Dishwasher, the wash pump seal might be defective and needs replacement. Ensure the petcock or pump drain (if equipped) is shut and tight. Also, tighten any loose hoses or hose clamps on the wash pump.
Why is the rinse water not reaching the required temperature in my Jackson Dishwasher?
If the rinse water in your Jackson Dishwasher is not reaching the required temperature, check the rinse heater element for continuity; if it's open, replace the heater. Also, verify the operation and setting of the thermostats; replace if necessary. Replace the rinse thermometer if it is defective.
General| Model | TempStar Series |
|---|---|
| Voltage | 208-240V |
| Number of Wash Cycles | 1 |
| Color | Stainless Steel |
| Category | Dishwasher |
| Voltage Options | 208V, 240V |
| Capacity | 60-80 racks per hour |
| Water Consumption per Cycle | 0.5-1.0 gallons |
| Water Consumption per Rack | 0.84 gallons |
