JR Venture CP - Front Radio Bed;Cooling Shroud Installation

84 pages

To Next Page

To Previous Page

2-3

FRONT RADIO BED/COOLING FAN SHROUD INSTALLATION

3x10 mm Socket Head Bolt

(4)

2.6x10 mm Self-Tapping Screw

(4)

2.6x10 mm Self-Tapping Screw (4)

Cooling Fan Shroud

3x10 mm Socket Head Bolt (4)

Front Radio Bed

Main Page

Assembly Instructions1
Table of Contents2
Section Description2
Introduction3
Venture 30 CP ARF Features4
Radio System Requirements4
Engine Requirements5
Building Supplies5
Required Tools6
Required Field Equipment6
Hardware Identification7
Tail Boom Installation8
Drive Belt Connection and Adjustment8
Tail Boom Brace Installation9
Tail Fin Attachment9
Tail Control Rod Assembly10
Tail Control Rod Installation/Horizontal Fin Attachment10
Engine Mount/Cooling Fan Installation11
Clutch Assembly Attachment11
Clutch Assembly Attachment12
Starter Shaft/Hex Adapter Installation12
Engine Installation13
Muffler Installation13
Servo Installation14
Gyro/Receiver/Switch Harness/Battery Installation15
Gyro/Receiver/Switch Harness/Battery Installation16
Understanding Swashplate Control Systems17
Understanding Swashplate Control Systems18
How JR 120 CCPM Works19
Radio System Requirements19
CCPM Software Activation and Initial Adjustment20
CCPM Software Activation and Initial Adjustment23
Important CCPM Programming Guidelines24
CCPM Servo Arm Preparation and Installation25
CCPM Servo Centering with the Sub-Trim Function26
CCPM Servo Centering with the Sub-Trim Function27
CCPM Linkage Connection28
Checking the Swashplate for Level29
Pitch-To-Aileron Mixing Adjustment with Travel Adjust30
Pitch-To-Elevator Mixing Adjustment with Travel Adjust31
Tail Control Rod Servo Connection32
Throttle Linkage Installation33
Body Assembly/Canopy Attachment34
Decal Attachment35
Main Rotor Blade Balancing36
Main Rotor Blade Attachment36
Optional 3D Control System Setup37
Optional 3D Control System Setup38
Radio Data Sheet: XP652/662 Basic Setup39
Radio Data Sheet: XP652/662 3D Setup40
Radio Data Sheet: X-378 Basic Setup41
Radio Data Sheet: X-378 3D Setup42
Radio Data Sheet: XP8103 Basic Setup43
Radio Data Sheet: XP8103 3D Setup44
Radio Data Sheet: PCM10X 3D Setup45
Final Servo Adjustment and Radio Setup47
Final Servo Adjustment and Radio Setup49
Final Preflight Check50
Blade Tracking Adjustment50
Blade Tracking Identification50
Advice and Basic Hover Training Practices51
General Maintenance52
Troubleshooting Guide53
Preassembled Components54
Clutch Bell Assembly54
Tail Drive Pinion/Bearing Assembly54
Elevator Arm Assembly55
Fuel Tank Assembly55
Main Frame Section Assembly56
Main Frame Clutch/Tail Pinion/Elevator/Fuel Tank57
Front Radio Bed/Cooling Shroud Installation58
Main Drive Gear/Autorotation Assembly Installation59
Landing Gear Assembly Installation60
Flybar Control Arm/Seesaw Arm Assembly61
Main Blade Holder Attachment61
Main Blade Holder Assembly62
Washout Assembly63
Swashplate Assembly63
Tail Pitch Plate Assembly64
Swashplate/Washout Assembly Installation64
Rotor Head Installation65
Flybar Installation65
Flybar Paddle Attachment66
Rotor Head/Swashplate Control Rod Installation66
Tail Gear Case Preparation67
Tail Gear Case Assembly67
Tail Center Hub Assembly68
Tail Blade Holder Assembly68
Tail Pitch Control Lever Installation69
Tail Boom Brace Assembly69
Parts Diagrams/Parts Listings70

JR Venture CP - Front Radio Bed;Cooling Shroud Installation

Table of Contents

Related product manuals